参数资料
| 型号： | ISL6267HRZ |
| 厂商： | Intersil |
| 文件页数： | 28/33页 |
| 文件大小： | 0K |
| 描述： | IC PWM CTRLR MULTIPHASE 48TQFN |
| 标准包装： | 50 |
| 系列： | Robust Ripple Regulator™ (R³) |
| 应用： | 控制器，AMD Fusion? CPU GPU |
| 输入电压： | 4.5 V ~ 25 V |
| 输出数： | 2 |
| 输出电压： | 0.013 V ~ 1.55 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页
ISL6267
that the ISEN voltages have minimal ripple and represent the DC
the state of VR_HOT, is defined in Equation 38.
--------------- = 14.7k
current flowing through the inductors. Recommended values are
R s = 10k Ω and C s = 0.22μF.
0.88V
60 μ A
(EQ. 38)
NTC Thermal Monitors and VR_HOT Function
The ISL6267 features three pins (NTC, NTC_NB, and VR_HOT)
which are allow the IC to monitor board temperature and alert
The equivalent resistance at the typical reset threshold voltage of
0.92V required to change the state of VR_HOT back low, is
defined in Equation 39
--------------- = 15.3k
the AMD CPU of a thermal issue. Figure 30 shows the thermal
monitor feature of the ISL6267. An NTC network is connected
between the NTC and NTC_NB pins and GND. The controller
0.92V
60 μ A
(EQ. 39)
drives a 60μA current source out of the NTC pin and the NTC_NB
pin alternatively at 1kHz frequency with 50% duty cycle. The
pulsed current flows through the respective NTC resistor network
on the pins and creates a voltage that is compared to an
over-temperature trip threshold. If the voltage on both NTC pins is
higher than the over-temperature trip threshold, then VR_HOT is
pulled up by an external resistor on the pin.
The NTC thermistor value correlates this resistance change to the
required temperature hysteresis. A standard 1% resistor is
typically needed to meet the NTC pin threshold voltage.
For example, a Panasonic NTC thermistor with B = 4700 has a
resistance ratio of 0.03322 of its nominal value at +105°C and
0.03956 of its nominal value at +100°C. The required resistance
of the NTC is defined in Equation 40.
------------------------------------------------------- = 94.6k Ω
NTC
( 15.3k Ω – 14.7k Ω )
( 0.03956 – 0.03322 )
(EQ. 40)
R p
+
V NTC
-
R NTC
R s
SW1
SW2
60μA
VR_HOT
MONITOR
+V
R
The closest, larger thermistor value for B = 4700 is 100k Ω . The
NTC thermistor part number is ERTJ1VV104.
At +105°C, a 100k Ω NTC resistance drops to
(0.03322 x 100k Ω ) = 3.322k Ω . With a 60μA current flowing out
of the NTC pin, the voltage drop across the resistor is only
(3.322k Ω x 60μA) = 0.199V. This value is much lower than the
NTC_NB
SW1 SW2
threshold voltage of 0.88V. A standard resistor, 1% tolerance,
added in series with the thermistor is required to raise the
(EQ. 41)
--------------- – 3.322k Ω = 11.34k Ω
R p
+
V NTC
-
R NTC
INTERNAL TO
ISL6267
voltage on the pin. The resistance required to meet the trip
threshold is calculated in Equation 41.
0.88V
60 μ A
R s
FIGURE 30. CIRCUITRY ASSOCIATED WITH THE THERMAL
MONITOR FEATURE OF THE ISL6267
As the board temperature rises, the NTC thermistor resistance
decreases and the voltage at the NTC pin drops. When the
voltage on the NTC pin drops below the over-temperature trip
threshold, then VR_HOT is pulled low. The VR_HOT signal is used
to change the CPU operation and decrease power consumption.
With the reduction in power consumption by the CPU, the board
temperature decreases and the NTC thermistor voltage rises.
Once the over-temperature threshold is tripped and VR_HOT is
taken low, the over-temperature threshold changes to the reset
level. The addition of hysteresis to the over-temperature
threshold prevents nuisance trips. Once both pin voltages exceed
the over-temperature reset threshold, the pull-down on VR_HOT
is released. The signal changes state and the CPU resumes
normal operation. The over-temperature threshold returns to the
trip level.
Selection of the NTC components can vary depending on how the
resistor network is configured. The equivalent resistance at the
typical over-temperature threshold voltage of 0.88V, to change
28
The closest, standard 1% tolerance resistor is 11.3k Ω .
The NTC thermistor is placed in a hot spot on the board, typically
near the upper MOSFET of channel 1 of the respective output.
The standard resistor is placed next to the controller.
January 8, 2013
FN7801.1
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6268CAZ | IC REG CTRLR BUCK PWM 16-QSOP |
| ISL6269AIRZ | IC REG CTRLR BUCK PWM 16-QFN |
| ISL6269BIRZ | IC REG CTRLR BUCK PWM 16-QFN |
| ISL6269IRZ | IC REG CTRLR BUCK PWM 16-QFN |
| ISL6271ACR-T | IC PMIC XSCALE PROCESSOR 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6267HRZ-T | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLR FOR AMD FUSION UP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6268 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Performance Notebook PWM Controller |
| ISL6268CAZ | 功能描述:IC REG CTRLR BUCK PWM 16-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6268CAZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6268EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL6268 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。