- 您现在的位置：买卖IC网 > PDF目录69009 > M30240M5-XXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M30240M5-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 22/139页 |
| 文件大小： | 1453K |
| 代理商： | M30240M5-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页
118
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Precautions
1.3.1.3 Dedicated Input Pins
If a dedicated input pin is connected to a power supply different from the supply that Vcc is connected
to, a resistor (approximately 1k ohm) should be added between the input pin and the connected power
supply. However, if the dedicated input pin voltage is higher than Vcc, latch up could occur.
A resistor is not required when using a Vcc voltage equal or greater than the voltage of the dedicated
input pin.
1.3.1.4 DMAC
DMA enable bit
The DMA enable bit is assigned to bit 3 of the DMA0 and DMA1 control registers. DMA becomes ac-
tive when the DMA enable bit is set to “1”. Immediately after the DMA becomes active, the data trans-
fers start and perform the following operations:
Reloads the value of the source pointer or destination pointer depending on which is specified for the
forward direction address pointer
Reloads the value of the transfer counter reload register to the transfer counter.
Thus overwriting “1” to the DMA enable bit with the DMAC being inactive carries out the operations
given above, so the DMAC operates again from the initial state at the instant “1” is overwritten to the
DMA enable bit.
DMA request bit
The DMA request bit turns to “1” if the DMA transfer request signal occurs regardless of the DMAC’s
state (regardless of weather the DMA enable bit is set to “1” or to “0”). It turns immediately before data
transfer starts.
In addition, it can be set to “0” by the use of a program, but cannot be set to “1”.
There can be instances in which a change in DMA request factor selection bit causes the DMA request
bit to turn to “1”. So be sure to set the DMA request bit to “0” after the DMA request factor selection bit
is changed.
The DMA request bit turns to “1” if a DMA transfer request signal occurs, and turns to “0” immediately
before data transfer starts. If the DMAC is active, data transfer starts immediately, so the value of the
DMA request bit, if read by use of a program, turns to be “0” in most cases. To examine whether the
DMAC is active, read the DMA enable bit.
To best judge the state of the DMAC, the DMA enable bit should be read instead of the DMA request
bit.
1.3.1.5 Frequency Synthesizer
Refer to Section 1.5.1.2 for setup procedures required after a hardware reset.
Set the value of the Frequency Synthesizer Prescaler register (FSP) so that fPIN is 1 MHZ or higher.
1.3.1.6 Interrupt
Reading address 0000016
When a maskable interrupts occurs, the CPU reads the interrupt information (the interrupt number
and interrupt request level) in the interrupt sequence.
The interrupt request bit of the corresponding interrupt written in address 0000016 is then set to “0”.
Do not read address 0000016 by software.
Reading address 0000016 by software sets the highest priority enabled interrupt source request bit to “0”
Therefore the interrupt routine may not be executed even though the interrupt is generated.
Setting the stack pointer
相关PDF资料 |
PDF描述 |
|---|---|
| M30240M6-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M5-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M6-XXXXFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M30240M6 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M6-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M8 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。