- 您现在的位置：买卖IC网 > PDF目录69009 > M30240M5-XXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M30240M5-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 26/139页 |
| 文件大小： | 1453K |
| 代理商： | M30240M5-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页
121
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Precautions
1.3.1.13 Timer A (Pulse-width Modulation mode)
1. The Timer Ai interrupt request bit becomes “1” if setting operation mode of the timer in compliance
with any of the following procedures:
Selecting PWM mode after reset.
Changing operation mode from timer mode to PWM mode.
Changing operation mode from event counter mode to PWM mode.
Therefore, to use Timer Ai interrupt (interrupt request bit), set Timer Ai interrupt request bit to “0” after
the above listed changes have been made.
2. Setting the count start flag to “0” while PWM pulses are being output causes the counter to stop
counting. If the TAiOUT pin is outputting an “H” level in this instance, the output level goes to “L”, and
the Timer Ai interrupt request bit goes to “1”. If the TAiOUT pin is outputting an “L” level in this instance,
the level does not change, and the Timer Ai interrupt request bit does not become “1”.
1.3.1.14 Timer B (Timer mode)
Reading the Timer Bi register while a count is in progress allows reading, with arbitrary timing, the val-
ue of the counter. Reading the Timer Bi register with the reload timing gets “FFFF16”. Reading the Tim-
er Bi register after setting a value in the Timer Bi register with a count halted but before the counter
starts counting gets a proper value.
1.3.1.15 UART2
When using UART2 in clock asynchronous serial I/O mode (UART), use the internal clock only, oth-
erwise, one of the following may occur:
The interrupt may not be issued at the end of the data transmission when the hardware transfers the
data from the transmit buffer to the transmit register.
Data may be corrupted when the hardware transfers data fro the transmit buffer register to the trans-
mit register. This only applies to UART2 asynchronous serial I/O mode and does not apply to UART0
or UART1.
1.3.1.16 USB
When the USB Reset Interrupt Status flag is set to “1”, the contents in the USB internal register (ad-
dresses 030016-033516) will return to their reset values. However, the following registers are not af-
fected by a USB Reset:
USB Control register (USBC)
Frequency Synthesizer Control register (FSC)
USB Endpoint x FIFO (addresses 033816 -033C16)
All LPF pin passive components must be located as close as possible to the LPF pin.
An insulation connector (Ferrite beads) must be connected between the AVss and digital Vss pins,
and between AVcc and digital Vcc pins.
When using DC-DC converter to supply 3.3V to the drive, connect a capacitor between the EXTCAP
pin and the Vss pin. The connection should consist of a 2.2
F capacitor (tantalum capacitor) and a
0.1
F capacitor (ceramic capacitor) connected in parallel. Use a ceramic capacitor equivalent to the
X7R type as a 0.1
F capacitor.
Connect a 27-33
resistor between the USB D+ and USB D- pins to meet USB specification imped-
ance requirements.
Connect a ceramic capacitor (33pF recommended) after the resistor between USB D+ and USB D-
or between USB D+/D- pins and the Vss pin to control the slew rate and rise/fall timing. This cap
should be placed after the 27-33
resistor. See section 1.5 for more details.
Connect a 1.5k
resistor between the EXTCAP pin and the USB D+ pin during normal operation.
Connect a 1.5k
resistor between the P8
3/ATTACH pin and the USB D+ pin and leave the EXTCAP
open when using Attach/Detach function.
Read or write to the USB internal registers (address 030016-033C16) by 8-bit mode only. Accessing
by 16-bit mode will cause incorrect read/write values.
相关PDF资料 |
PDF描述 |
|---|---|
| M30240M6-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M5-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M6-XXXXFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M30240M6 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M6-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M8 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。