- 您现在的位置：买卖IC网 > PDF目录69009 > M30240M5-XXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M30240M5-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 40/139页 |
| 文件大小： | 1453K |
| 代理商： | M30240M5-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页
134
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Frequency Synthesizer
Change the DC-DC converter from high current mode to low current mode by setting USBC3 (bit 3
of the USBC) to a “1”
Disable the USB clock by setting USBC5 (bit 5 of USBC) to a “0”. Once the USB clock is disabled,
registers internal to the USB FCU should not be written to. This includes all USB SFRs from address
030016 to 033C16. It does not include USBC or FSC.
Perform other tasks to reduce total current to below 500
A.
Disable the PLL by setting FSE (bit 0 of FSC) to a “0”.
Make sure the I-FLAG is set to “1”.
Stop the system clock by setting CM10 (bit 0 of CM1) to a “1”. Make sure to first enable writing to the
system clock control register by setting PRCO (bit 0 of PRCR) to “1’. Also, make sure to enable the
USB Resume Interrupt (RSMIC register) and clear or execute any pending interrupts prior to stop-
ping the clock so the MCU can wake up once resume signaling is detected. If the clock is stopped
using an interrupt routine, make sure to set the priority of the Resume Interrupt (RSMIC) higher than
the current interrupt.
Note that no action may be necessary if the device is self powered.
1.5.1.6 Set up after USB Resume Signaling Detected
A resume occurs when the USB FCU is in the suspend state and detects a non-idle signaling on D+/
D-. Detection of a resume results in bit 6 of USBIS2 and bit 1 of USBPM (RESUME) being set to a “1”.
This causes bit 3 of RSMIC to also be set to “1”. If the MCU was in the stop state prior to the detection
of the resume, the USB Resume Interrupt request will cause the MCU to wake up from the stop state.
Bit 6 of USBIS2 needs to be cleared (by writing a “1” to the bit) in order to allow a future resume event.
See section 2.9 “Stop Mode” for details on waking up from the stop state.
The configuration of the frequency synthesizer and DC-DC converter should be changed as follows in
the USB Resume Interrupt routine (if the device is bus powered):
Re-enable the PLL for 48MHz f(VCO) by setting FSE (bit 0 of the FSC) to a “1”, then wait for 2 ms.
Wait for 2 ms.
Check the lock status bit (LS, bit 7 of FSC).
If the bit is a “1”, continue.
If the bit is a “0”, wait 0.1
ms longer and then re-check the bit.
Enable the USB clock by setting USBC5 (bit 5 of USBC) to a “1”.
Wait for a minimum of 4 cycles.
Change the DC-DC converter from low current mode to high current mode by setting USBC3 (bit 3
of the USBC) to a “0”.
Enable other blocks as necessary.
Registers internal to the USB FCU should not be written to until the USB clock is re-enabled. This in-
cludes all USB SFRs from address 030016 to 033C16. It does not include USBC or FSC.
Note that the configuration changes described above may not need to be made if the MCU was not
placed in a suspend state as described in section 5.1.2.3 Set up after USB Suspend Detected.
1.5.1.7 PLL Lock Bit
The PLL lock bit is used to indicate when the PLL is first locked. Accordingly, after the PLL is enabled
and it has been given 2.0 ms to stabilize, the lock bit status should be checked. Once the lock bit is
HIGH, the USB check should be enabled. After this stage, the lock bit is no longer valid and should
not be monitored, unless the PLL is re-enabled.
相关PDF资料 |
PDF描述 |
|---|---|
| M30240M6-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M5-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M6-XXXXFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M30240M6 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M6-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M8 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。