参数资料
型号: M30240M5-XXXFP
元件分类: 微控制器/微处理器
英文描述: 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
封装: 0.80 MM PITCH, PLASTIC, QFP-80
文件页数: 77/139页
文件大小: 1453K
代理商: M30240M5-XXXFP
42
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Universal Serial Bus
1.2.18.1.2 Generic Function Interface
The GFI handles all USB standard requests from the host through the control endpoint (endpoint zero), han-
dles Bulk, Isochronous and Interrupt transfers through Endpoints 1-4. The GFI handles read pointer reversal
for re-transmission the current data set; write pointer reversal for reception of the last data set again and data
toggle synchronization.
1.2.18.1.3 Serial Engine Interface Unit
The SIU block decodes the Address and Endpoint fields from the USB host.
1.2.18.1.4 Microcontroller Interface
The MCI block handles the Microcontroller interface and performs address decoding and synchronization of
control signals.
1.2.18.1.5 USB Transceiver
The USB transceiver, designed to interface with the physical layer of the USB, is compliant with the USB Spec-
ification (version 1.1) for full-speed devices. It consists of two 6-ohm drivers, a receiver, and Schmitt triggers
for single-ended receive signals.
The transceiver also includes a voltage converter. The voltage converter can supply 3.0 - 3.6V to the trans-
mitter when the rest of the chip (CPU, USB FCU) operates at 4.15 - 5.25V. To enable the voltage converter,
set bit 4 of the USB Control Register (USBC) to a “1”. To disable the voltage converter, set bit 4 of the USBC
to a “0”. Refer to Section 1.5.4 “USB Transceiver” for more detailed information.
Figure 1.29: USB Function Control Unit Block Diagram
1.2.18.2 USB Interrupts
There are five USB interrupts in this device:
USB Function interrupt
USB Reset interrupt
USB Suspend interrupt
USB Resume interrupt
USB Start-of-Frame (SOF) interrupt.
The first four interrupts are used to control the data flow and USB power. The SOF interrupt is used
to monitor the transfer of isochronous (ISO) data. Each of the five USB interrupts is enabled by setting
the corresponding bit in the Interrupt Control Register of the Interrupt Control Unit. Because the USB
Function Interrupt has multiple interrupt sources, another level of enabling is within the USB Interrupt
Registers 1 & 2.
CPU
MCI
SIU
GFI
FIFOs
SIE
T
ran
sc
ei
ve
r
D+
D-
相关PDF资料
PDF描述
M30240M6-XXXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M30240ECFP 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80
M30240M5-XXXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M30240M6-XXXXFP 16-BIT, OTPROM, MICROCONTROLLER, PQFP80
M30240ECFP 16-BIT, OTPROM, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
M30240M6 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M6-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M7 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M7-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M8 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER