参数资料
型号: M30240M5-XXXFP
元件分类: 微控制器/微处理器
英文描述: 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
封装: 0.80 MM PITCH, PLASTIC, QFP-80
文件页数: 38/139页
文件大小: 1453K
代理商: M30240M5-XXXFP
132
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Frequency Synthesizer
1.5.1.2 Set up of Frequency Synthesizer and DC-DC Converter
Figure 1.117: PLL, DC-DC Converter and USB Functional Block Diagram
A functional block diagram of the USB system on the M30240 which shows how the control signals
affect operation is given in Figure 1.117
1.5.1.3 Set up after Hardware Reset
A Hardware Reset occurs when either the RESET pin is brought low for more than 2
s or an invalid
opcode is fetched by the CPU. The frequency synthesizer (PLL) and DC-DC converter should be set
up as follows in the Hardware Reset routine (see Figure 1.118),
Power up the M30240 and other components on the peripheral device for less than 100 mA opera-
tion. The current limit only applies for bus powered devices.
Configure the PLL for 48MHz f(VCO) operation.
Enable the PLL by setting FSE (bit 0 of the Frequency Synthesizer Control Register (FSC)) to a “1”,
then wait for 2 ms.
Check the lock status bit (LS, bit 7 of FSC).
If the bit is a “1”, go on.
If the bit is a “0”, wait 0.1 ms longer and then re-check the bit.
Enable the DC-DC converter in high current mode by setting USBC4 (bit 4 of the USB Control Reg-
ister (USBC)) to a “1” and keeping USBC3 (bit 3 of USBC) a “0”. High current mode should always
be used during normal USB operation. Low current mode should only be used during a USB sus-
pend.
Wait (C + 1)ms (where C equals the external capacitance connected to the Ext Cap pin in
F) for
the voltage on Ext Cap to reach a steady state voltage of approximately 3.3V. (Since the D+ pullup
is connected to the Ext Cap pin, the upstream hub will detect that the peripheral device has been
plugged in once the voltage on D+ reaches approximately 2.0 V.)
Example: A 2.2
F capacitor connected to Ext Cap requires 3.2 ms for the voltage on Ext Cap to be stable.
Enable the USB clock by setting USBC5 (bit 5 of USBC) to a “1”. (If the USB clock and FCU are
enabled before the voltage on Ext Cap is stable, a phantom USB Reset may be detected, or the ac-
tual USB Reset may not be detected.)
Wait at least 4 cycles of
Φ, then enable the USB FCU by setting USBC7 (bit 7 of USBC) to a “1”.
Enable other blocks as necessary.
27-33
27-33
D+
D-
USB FCU
2.2
F
0.1
F
Ext Cap
Frequency
Synthesizer
f(Xin)
FSE
LS
1.
5
k
USB Transceiver
DC-DC Converter
USBC3
USBC4
USBC7
USBC5
USBCLK
(48MHz)
enable
lock
enable
(enable)
enable
current
mode
相关PDF资料
PDF描述
M30240M6-XXXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M30240ECFP 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80
M30240M5-XXXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M30240M6-XXXXFP 16-BIT, OTPROM, MICROCONTROLLER, PQFP80
M30240ECFP 16-BIT, OTPROM, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
M30240M6 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M6-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M7 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M7-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240M8 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER