参数资料
型号: MC68HC05V7FN
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC68
封装: PLASTIC, LCC-68
文件页数: 140/170页
文件大小: 589K
代理商: MC68HC05V7FN
SECTION 8: LOW-POWER MODES
MOTOROLA
Page 57
MC68HC05V7 Specification Rev. 1.0
SECTION 8
LOW-POWER MODES
The MC68HC05V7 is capable of running in one of several low-power operational modes.
The WAIT and STOP instructions provide two modes that reduce the power required for
the MCU by stopping various internal clocks and/or the on-chip oscillator. The STOP and
WAIT instructions are not normally used if the COP Watchdog Timer is enabled. A mask
option is provided to convert the STOP instruction to an internal reset. The flow of the STOP
and WAIT modes is shown in Figure 8-2.
8.1
STOP INSTRUCTION
The STOP instruction can result in one of two operations depending on the Mask Options.
If the STOP option is enabled, the STOP instruction operates like the STOP in normal
MC68HC05 family members and places the device in the low power STOP Mode. If the
STOP option is disabled, the STOP instruction will cause a chip reset when executed.
8.1.1
STOP MODE
Execution of the STOP instruction, with the proper mask option, places the MCU in its
lowest power consumption mode. In the STOP Mode the internal oscillator is turned off,
halting
all internal processing, including the COP Watchdog Timer.
During the STOP mode, the TCR bits are altered to remove any pending timer interrupt
request and to disable any further timer interrupts. The timer prescaler is cleared. The I bit
in the CCR is cleared and the IRQE mask is set in the ICSR to enable external interrupts.
All other registers and memory remain unaltered. All input/output lines remain unchanged.
The processor can be brought out of the STOP mode only by an external interrupt or reset.
The MCU can be brought out of the STOP Mode by only one of the following:
IRQ pin external interrupt
Externally or internally generated RESET
Falling edge on any Port A or Port C pin (if enabled)
Rising edge on the MDLC BUS pin
When exiting the STOP Mode, the internal oscillator will resume after a 4064 internal
processor clock cycle oscillator stabilization delay, as shown in Figure 8-1.
NOTE:
Execution of the STOP instruction with the proper mask option will cause
the oscillator to stop and therefore disable the COP Watchdog Timer. If
the COP Watchdog Timer is to be used, the STOP Mode should be
disabled by selecting the proper mask option. See 6.2.3.4 COP
相关PDF资料
PDF描述
MC68HC05V7CB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56
MC68HC05V7CFU 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP64
MC68HC05X16FU 8-BIT, MROM, MICROCONTROLLER, PQFP64
MC68HC705X32FU 8-BIT, OTPROM, MICROCONTROLLER, PQFP64
MC68HC05X16MFU 8-BIT, MROM, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
MC68HC05X16 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor HCMOS) microcontroller unit
MC68HC05X32 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor HCMOS) microcontroller unit
MC68HC05X4 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
MC68HC05X4CDW 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
MC68HC05X4DW 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit