- 您现在的位置：买卖IC网 > PDF目录45323 > MP80C31-12D (ATMEL CORP) 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | MP80C31-12D |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 123/170页 |
| 文件大小： | 4133K |
| 代理商： | MP80C31-12D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页当前第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页
56
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
Count
Increment or decrement TCNT0 by 1.
Direction
Select between increment and decrement.
Clear
Clear TCNT0 (set all bits to zero).
clk
T0
Timer/Counter clock.
TOP
Signalize that TCNT0 has reached maximum value.
BOTTOM
Signalize that TCNT0 has reached minimum value (zero).
The 16-bit counter is mapped into two 8-bit I/O memory locations: Counter High (TCNT0H) containing the upper
eight bits of the counter, and Counter Low (TCNT0L) containing the lower eight bits. The TCNT0H Register can
only be indirectly accessed by the CPU. When the CPU does an access to the TCNT0H I/O location, the CPU
accesses the high byte temporary register (TEMP). The temporary register is updated with the TCNT0H value
when the TCNT0L is read, and TCNT0H is updated with the temporary register value when TCNT0L is written. This
allows the CPU to read or write the entire 16-bit counter value within one clock cycle via the 8-bit data bus. It is
important to notice that there are special cases of writing to the TCNT0 Register when the counter is counting that
will give unpredictable results. The special cases are described in the sections where they are of importance.
Depending on the mode of operation used, the counter is cleared, incremented, or decremented at each timer
clock (clk
T0). The clkT0 can be generated from an external or internal clock source, selected by the Clock Select bits
(CS02:0). When no clock source is selected (CS02:0 = 0) the timer is stopped. However, the TCNT0 value can be
accessed by the CPU, independent of whether clk
T0 is present or not. A CPU write overrides (has priority over) all
counter clear or count operations.
The counting sequence is determined by the setting of the Waveform Generation mode bits (WGM03:0) located in
the Timer/Counter Control Registers A and B (TCCR0A and TCCR0B). There are close connections between how
the counter behaves (counts) and how waveforms are generated on the Output Compare outputs OC0x. For more
details about advanced counting sequences and waveform generation, see “Modes of Operation” on page 61.
The Timer/Counter Overflow Flag (TOV0) is set according to the mode of operation selected by the WGM03:0 bits.
TOV0 can be used for generating a CPU interrupt.
11.5
Input Capture Unit
The Timer/Counter incorporates an Input Capture unit that can capture external events and give them a time-
stamp indicating time of occurrence. The external signal indicating an event, or multiple events, can be applied via
the ICP0 pin. The time-stamps can then be used to calculate frequency, duty-cycle, and other features of the signal
applied. Alternatively the time-stamps can be used for creating a log of the events.
The Input Capture unit is illustrated by the block diagram shown in Figure 11-5 on page 57. The elements of the
block diagram that are not directly a part of the Input Capture unit are gray shaded. The lower case “n” in register
and bit names indicates the Timer/Counter number.
相关PDF资料 |
PDF描述 |
|---|---|
| MF280C51-20R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44 |
| MS80C51-30R | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44 |
| MS80C51-20D | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44 |
| MF280C31-25R | 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 |
| MF180C31-16D | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP81 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:BRIDGE RECTIFIERS |
| MP810 | 制造商:GOOD-ARK 制造商全称:GOOD-ARK Electronics 功能描述:SILICON BRIDGE RECTIFIERS |
| MP-810 | 制造商:JAMECO BENCHPRO 功能描述:4-Piece Plier/Cutter/Screwdrivers Set |
| MP8100 | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier |
| MP8100DS | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier |
发布紧急采购，3分钟左右您将得到回复。