- 您现在的位置：买卖IC网 > PDF目录45323 > MP80C31-12D (ATMEL CORP) 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | MP80C31-12D |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 169/170页 |
| 文件大小： | 4133K |
| 代理商： | MP80C31-12D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页当前第169页第170页
98
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
Figure 14-6. Data changing and Data sampling.
The TPI physical layer supports two modes of operation: Transmit and Receive. By default, the layer is in Receive
mode, waiting for a start bit. The mode of operation is controlled by the access layer.
14.3.7
Serial Data Reception
When the TPI physical layer is in receive mode, data reception is started as soon as a start bit has been detected.
Each bit that follows the start bit will be sampled at the rising edge of the TPICLK and shifted into the shift register
until the second stop bit has been received. When the complete frame is present in the shift register the received
data will be available for the TPI access layer.
There are three possible exceptions in the receive mode: frame error, parity error and break detection. All these
exceptions are signalized to the TPI access layer, which then enters the error state and puts the TPI physical layer
into receive mode, waiting for a BREAK character.
Frame Error Exception. The frame error exception indicates the state of the stop bit. The frame error exception
is set if the stop bit was read as zero.
Parity Error Exception. The parity of the data bits is calculated during the frame reception. After the frame is
received completely, the result is compared with the parity bit of the frame. If the comparison fails the parity
error exception is signalized.
Break Detection Exception. The Break detection exception is given when a complete frame of all zeros has
been received.
14.3.8
Serial Data Transmission
When the TPI physical layer is ready to send a new frame it initiates data transmission by loading the shift register
with the data to be transmitted. When the shift register has been loaded with new data, the transmitter shifts one
complete frame out on the TPIDATA line at the transfer rate given by TPICLK.
If a collision is detected during transmission, the output driver is disabled. The TPI access layer enters the error
state and the TPI physical layer is put into receive mode, waiting for a BREAK character.
14.3.9
Collision Detection Exception
The TPI physical layer uses one bi-directional data line for both data reception and transmission. A possible drive
contention may occur, if the external programmer and the TPI physical layer drive the TPIDATA line simultane-
ously. In order to reduce the effect of the drive contention, a collision detection mechanism is supported. The
collision detection is based on the way the TPI physical layer drives the TPIDATA line.
The TPIDATA line is driven by a tri-state, push-pull driver with internal pull-up. The output driver is always enabled
when a logical zero is sent. When sending successive logical ones, the output is only driven actively during the first
clock cycle. After this, the output driver is automatically tri-stated and the TPIDATA line is kept high by the internal
pull-up. The output is re-enabled, when the next logical zero is sent.
TPIDATA
TPICLK
SAMPLE
SETUP
相关PDF资料 |
PDF描述 |
|---|---|
| MF280C51-20R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44 |
| MS80C51-30R | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44 |
| MS80C51-20D | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44 |
| MF280C31-25R | 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 |
| MF180C31-16D | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP81 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:BRIDGE RECTIFIERS |
| MP810 | 制造商:GOOD-ARK 制造商全称:GOOD-ARK Electronics 功能描述:SILICON BRIDGE RECTIFIERS |
| MP-810 | 制造商:JAMECO BENCHPRO 功能描述:4-Piece Plier/Cutter/Screwdrivers Set |
| MP8100 | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier |
| MP8100DS | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier |
发布紧急采购，3分钟左右您将得到回复。