- 您现在的位置：买卖IC网 > PDF目录45323 > MP80C31-12D (ATMEL CORP) 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | MP80C31-12D |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 125/170页 |
| 文件大小： | 4133K |
| 代理商： | MP80C31-12D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页当前第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页
58
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
clock cycles. Note that the input of the noise canceler and edge detector is always enabled unless the Timer/Coun-
ter is set in a Waveform Generation mode that uses ICR0 to define TOP.
An Input Capture can be triggered by software by controlling the port of the ICP0 pin.
11.5.2
Noise Canceler
The noise canceler improves noise immunity by using a simple digital filtering scheme. The noise canceler input is
monitored over four samples, and all four must be equal for changing the output that in turn is used by the edge
detector.
The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNC0) bit in Timer/Counter Control
Register B (TCCR0B). When enabled the noise canceler introduces additional four system clock cycles of delay
from a change applied to the input, to the update of the ICR0 Register. The noise canceler uses the system clock
and is therefore not affected by the prescaler.
11.5.3
Using the Input Capture Unit
The main challenge when using the Input Capture unit is to assign enough processor capacity for handling the
incoming events. The time between two events is critical. If the processor has not read the captured value in the
ICR0 Register before the next event occurs, the ICR0 will be overwritten with a new value. In this case the result of
the capture will be incorrect.
When using the Input Capture interrupt, the ICR0 Register should be read as early in the interrupt handler routine
as possible. Even though the Input Capture interrupt has relatively high priority, the maximum interrupt response
time is dependent on the maximum number of clock cycles it takes to handle any of the other interrupt requests.
Using the Input Capture unit in any mode of operation when the TOP value (resolution) is actively changed during
operation, is not recommended.
Measurement of an external signal’s duty cycle requires that the trigger edge is changed after each capture.
Changing the edge sensing must be done as early as possible after the ICR0 Register has been read. After a
change of the edge, the Input Capture Flag (ICF0) must be cleared by software (writing a logical one to the I/O bit
location). For measuring frequency only, the clearing of the ICF0 flag is not required (if an interrupt handler is
used).
11.6
Output Compare Units
The 16-bit comparator continuously compares TCNT0 with the Output Compare Register (OCR0x). If TCNT equals
OCR0x the comparator signals a match. A match will set the Output Compare Flag (OCF0x) at the next timer clock
cycle. If enabled (OCIE0x = 1), the Output Compare Flag generates an Output Compare interrupt. The OCF0x flag
is automatically cleared when the interrupt is executed. Alternatively the OCF0x flag can be cleared by software by
writing a logical one to its I/O bit location. The Waveform Generator uses the match signal to generate an output
according to operating mode set by the Waveform Generation mode (WGM03:0) bits and Compare Output mode
(COM0x1:0) bits. The TOP and BOTTOM signals are used by the Waveform Generator for handling the special
cases of the extreme values in some modes of operation (“Modes of Operation” on page 61).
A special feature of Output Compare unit A allows it to define the Timer/Counter TOP value (i.e., counter resolu-
tion). In addition to the counter resolution, the TOP value defines the period time for waveforms generated by the
Waveform Generator.
Figure 11-6 on page 59 shows a block diagram of the Output Compare unit. The small “n” in the register and bit
names indicates the device number (n = 0 for Timer/Counter 0), and the “x” indicates Output Compare unit (A/B).
The elements of the block diagram that are not directly a part of the Output Compare unit are gray shaded.
相关PDF资料 |
PDF描述 |
|---|---|
| MF280C51-20R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44 |
| MS80C51-30R | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44 |
| MS80C51-20D | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44 |
| MF280C31-25R | 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 |
| MF180C31-16D | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP81 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:BRIDGE RECTIFIERS |
| MP810 | 制造商:GOOD-ARK 制造商全称:GOOD-ARK Electronics 功能描述:SILICON BRIDGE RECTIFIERS |
| MP-810 | 制造商:JAMECO BENCHPRO 功能描述:4-Piece Plier/Cutter/Screwdrivers Set |
| MP8100 | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier |
| MP8100DS | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier |
发布紧急采购，3分钟左右您将得到回复。