参数资料
型号: MP80C31-12D
厂商: ATMEL CORP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40
封装: PLASTIC, DIP-40
文件页数: 89/170页
文件大小: 4133K
代理商: MP80C31-12D
25
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
7.3.2
Analog to Digital Converter
If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be disabled before entering
any sleep mode. When the ADC is turned off and on again, the next conversion will be an extended conversion.
See “Analog to Digital Converter” on page 82 for details on ADC operation.
The ADC is available in ATtiny5/10, only.
7.3.3
Watchdog Timer
If the Watchdog Timer is not needed in the application, this module should be turned off. If the Watchdog Timer is
enabled, it will be enabled in all sleep modes, and hence, always consume power. In the deeper sleep modes, this
will contribute significantly to the total current consumption. Refer to “Watchdog Timer” on page 30 for details on
how to configure the Watchdog Timer.
7.3.4
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The most important thing
is then to ensure that no pins drive resistive loads. In sleep modes where the I/O clock (clk
I/O) is stopped, the input
buffers of the device will be disabled. This ensures that no power is consumed by the input logic when not needed.
In some cases, the input logic is needed for detecting wake-up conditions, and it will then be enabled. Refer to the
section “Digital Input Enable and Sleep Modes” on page 44 for details on which pins are enabled. If the input buffer
is enabled and the input signal is left floating or has an analog signal level close to V
CC/2, the input buffer will use
excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal level close to V
CC/2
on an input pin can cause significant current even in active mode. Digital input buffers can be disabled by writing to
the Digital Input Disable Register (DIDR0). Refer to “DIDR0 – Digital Input Disable Register 0” on page 81 for
details.
7.4
Register Description
7.4.1
SMCR – Sleep Mode Control Register
The SMCR Control Register contains control bits for power management.
Bits 7:4 – Res: Reserved Bits
These bits are reserved and will always read zero.
Bits 3:1 – SM2..SM0: Sleep Mode Select Bits 2..0
These bits select between available sleep modes, as shown in Table 7-2.
Bit
765
432
1
0
SM2
SM1
SM0
SE
SMCR
Read/Write
R
R/W
Initial Value
0
Table 7-2.
Sleep Mode Select
SM2
SM1
SM0
Sleep Mode
000
Idle
0
1
ADC noise reduction (1)
0
1
0
Power-down
011
Reserved
1
0
Standby
相关PDF资料
PDF描述
MF280C51-20R 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44
MS80C51-30R 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44
MS80C51-20D 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44
MF280C31-25R 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44
MF180C31-16D 8-BIT, 16 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
MP81 制造商:未知厂家 制造商全称:未知厂家 功能描述:BRIDGE RECTIFIERS
MP810 制造商:GOOD-ARK 制造商全称:GOOD-ARK Electronics 功能描述:SILICON BRIDGE RECTIFIERS
MP-810 制造商:JAMECO BENCHPRO 功能描述:4-Piece Plier/Cutter/Screwdrivers Set
MP8100 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier
MP8100DS 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier