- 您现在的位置：买卖IC网 > PDF目录69040 > MT8952BPR (ZARLINK SEMICONDUCTOR INC) 1 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, PQCC28 PDF资料下载
参数资料
| 型号： | MT8952BPR |
| 厂商： | ZARLINK SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, PQCC28 |
| 封装： | PLASTIC, MS-018AB, LCC-28 |
| 文件页数： | 29/32页 |
| 文件大小： | 602K |
| 代理商： | MT8952BPR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页
MT8952B
Data Sheet
6
Zarlink Semiconductor Inc.
other than ‘GO Ahead’. The reception of this sequence is indicated by GA bit in the General Status Register and the
Protocol Controller can generate an interrupt if enabled to do so by the GA bit in the Interrupt Enable Register.
Transparent Data Transfer State
The Protocol Controller, in this state, disables the protocol functions defined earlier and provides bi-directional
access to the serial bit streams through the parallel port. Like other states, the transparent data transfer can be
selected in both timing modes.
Invalid Frames
Any frame shorter than 32 bits between the opening and closing flags (corresponding to 16 bits of data and 16 bits
FCS) is considered invalid. The Protocol Controller ignores the frame only if the frame length is less than 24 bits
between the flags. For frames of length 24 to 32 bits, it transfers the data field to FIFO and tags it as having bad
FCS in the FIFO Status Register.
Functional Description
The functional block diagram of the HDLC Protocol Controller is shown in Figure 1. It has two ports. The serial port
transmits and receives formatted data packets and the parallel port provides a microprocessor interface for access
to various registers in the Protocol Controller.
The serial port can be configured to operate in two modes depending on the IC bit in the Timing Control Register. It
can transmit/receive the packets on selected timeslots in ST- BUS format or it can, using the enable signals
(TxCEN and RxCEN), transmit/receive the packets at a bit rate equal to CKi clock input.
The microprocessor port allows parallel data transfers between the Protocol Controller and a 6800/6809 system
bus. This interface consists of Data Bus (D0-D7), Address Bus (A0-A3), E Clock, Chip Select (CS) and R/W control.
The micro-processor can read and write to the various registers in the Protocol Controller. The addresses of these
registers are given in Table 2. The IRQ is an open drain, active LOW output indicating an interrupt request to CPU.
Control and monitoring of many different interrupts that may originate from the protocol controller is implemented by
the Interrupt Flag Register (IFR) and the Interrupt Enable Register (IER). Specific events have been described that
set a bit HIGH in the Interrupt Flag Register. Such an event does not necessarily interrupt the CPU. To assert an
interrupt (pull IRQ output LOW) the bit in IER that coincides with the Interrupt Flag Register must be set HIGH. The
IRQ bit in the General Status Register is the complement of IRQ pin status. If an interrupt is asserted, this bit will be
set HIGH otherwise it will be LOW.
TEOP and REOP Outputs
The HDLC Protocol Controller provides two separate signals TEOP & REOP indicating the end of packet
transmitted and received respectively. TEOP is a HIGH going pulse for one bit duration asserted during the last bit
of the closing flag or Abort sequence of the transmit packet. REOP is also a HIGH going pulse occurring for one bit
period when a closing flag is received or an incoming packet is aborted or an invalid packet of 24 or more bits is
detected. However, REOP is not generated for invalid packets of length less than 24 bits. These ‘end of packet’
signals are useful in multiplexing several data links on to a single HDLC Protocol Controller.
Timing Modes
There are two timing modes the Protocol Controller can be run in. These timing modes refer only to the
configuration of the serial port and are not related to the microprocessor port.
Internal Timing Mode
The Internal Timing Mode is intended for an easy interface to various products using ST-BUS architecture,
particularly Zarlink’s Digital Network Interface Circuit (DNIC - MT8972). The data/packets are shifted in/out serially
in ST-BUS format using the timing signals F0i and C2i/C4i. In addition to framing the data, the Protocol Controller
相关PDF资料 |
PDF描述 |
|---|---|
| MT8952BP1 | 1 CHANNEL(S), 2.5M bps, SERIAL COMM CONTROLLER, PQCC28 |
| MTA41110/P | SPECIALTY MICROPROCESSOR CIRCUIT, PDIP18 |
| MTA41110/SO | SPECIALTY MICROPROCESSOR CIRCUIT, PDSO18 |
| MTR80C186-12 | 16-BIT, 12.5 MHz, MICROPROCESSOR, CQCC68 |
| MTA80C186-10 | 16-BIT, 10 MHz, MICROPROCESSOR, CPGA68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MT8952BPR1 | 制造商:Microsemi Corporation 功能描述:PB FREE HDLC CONTROLLER, PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE HDLC CONTROLLER, PLCC - Tape and Reel |
| MT8952BS | 制造商:Microsemi Corporation 功能描述: |
| MT8952BS1 | 制造商:Microsemi Corporation 功能描述:PB FREE HDLC PROTOCOL CONTROLLER - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE HDLC PROTOCOL CONTROLLER |
| MT8960 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:Integrated PCM Filter Codec |
| MT8960AE | 制造商:ZARLINK 功能描述: |
发布紧急采购，3分钟左右您将得到回复。