- 您现在的位置：买卖IC网 > PDF目录69321 > RFPIC12F675K-E/SS 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO20 PDF资料下载
参数资料
| 型号： | RFPIC12F675K-E/SS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO20 |
| 封装： | 0.209 INCH, PLASTIC, MO-150, SSOP-20 |
| 文件页数： | 75/123页 |
| 文件大小： | 5438K |
| 代理商： | RFPIC12F675K-E/SS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页当前第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页
2003 Microchip Technology Inc.
Preliminary
DS70091A-page 53
rfPIC12F675
9.6
Clock Output
The clock output is available to the microcontroller or
other
circuits
requiring
an
accurate
reference
frequency. This signal would typically be used to
correct the internal RC oscillator for system designs
that require accurate bit synchronization or tight time
division
multiplexing.
The
REFCLK
output
can
connect directly to the T0CKI or T1CKI.
The REFCLK output frequency is the crystal oscillator
divided by 4 on the rfPIC12F675K and rfPIC12F675F.
For the rfPIC12F675H the crystal oscillator is divided
by 8.
9.7
Phase-Locked Loop Filter
The LF pin connects to an internal node on the PLL
filter. Typically the pin should not be connected. In
specialized cases it may be necessary to load this pin
with extra capacitance to ground. Adding capacitance
reduces the loop filter bandwidth which trades off an
increase in phase noise for a reduction in clock spurs.
Useful diagnostic measurements can be taken on the
LF pin with a high impedance, low capacitance probe.
Measuring the time from RFEN going high until the LF
voltage stabilizes will determine the minimum delay
before the start of a transmission. For more information
on PLL filters refer to Application Note AN846 Basic
PLL Filters for the rfPIC/rfHCS.
9.8
Power Amplifier
The PLL output feeds the power amplifier (PA) which
drives the open-collector ANT output. The output
should be DC biased with an inductor to the V
DDRF
supply. The output impedance must be matched to the
load impedance to deliver the maximum power. This is
typically done with a transformer or tapped capacitor
circuit. Failure to match the impedance may cause
excessive spurious and harmonic emissions. For more
information on transformer matching see Application
Note AN831, Matching Small Loop Antennas to rfPIC
Devices. For more information on tapped capacitor
matching see Application Note AN242 Designing an
FCC Approved ASK rfPIC Transmitter.
The transmit output power can be adjusted in five
discrete steps from +9 dBm to -70 dBm by varying the
voltage on the PS pin. Since the PS pin has an internal
8
A source the voltage can be set with a resistor from
the PS pin to ground as shown in Figure 9-7. Some
possible resistor values to set the current are shown in
It is usually desirable to select the lowest power level
step that does not compromise communications reli-
ablity. The most important benefit is the conservation of
battery power. Another reason is to make it easier to
pass regulatory limits. And a third reason is to reduce
interference to other communications in the shared RF
spectrum. Small inefficient antennas will require higher
power level settings than larger efficient antennas.
FIGURE 9-7:
.POWER SELECT CIRCUIT
TABLE 9-4:
POWER SELECT RESISTOR SELECTION (1,2)
Layout considerations - Keep the clock trace short
and narrow yet as far as possible from other traces to
reduce capacitance and the associated current draw.
If the REFCLK trace must pass near the crystal and
LF nodes then shield them with ground traces.
Layout considerations - Keep traces short and if the
optional loop filter capacitor is required, place it as
close as possible to the LF pin with its own via to the
ground plane.
PS
rfPIC12F675
R1
VPS
IPS = 8 A
To power
select
circuitry
Power Step
Output Power
(dBm)
PS Voltage
(Volts)
R1 Resistance
(
)
RF Transmitter
Current (mA)
4
9
1.6
open
10.7
32
0.8
100k (3)
6.5
2-4
0.4
47k (3)
4.7
1
-12
0.2
22k (3)
3.5
0
-70
0.1
short
2.7
Note 1: Standard Operating Conditions, T
A = 25°C, RFEN = 1, VDDRF = 3V, fTRANSMIT = 433.92 MHz
2: Typical values, for complete specifications see data sheet Section 13.0.
3: R1 resistor variations plus I
PS current supply variations must not exceed VPS step limits.
相关PDF资料 |
PDF描述 |
|---|---|
| RFPIC12F675H-E/SS | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO20 |
| RH80530GZ001512 | 32-BIT, 1000 MHz, MICROPROCESSOR, CPGA478 |
| RH80530GZ009512 | 32-BIT, 1200 MHz, MICROPROCESSOR, CPGA478 |
| RJ80530GZ004512 | 32-BIT, 1066 MHz, MICROPROCESSOR, PBGA479 |
| RH80530GZ004512 | 32-BIT, 1066 MHz, MICROPROCESSOR, CPGA478 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RFPIC12F675K-I/SS | 功能描述:射频微控制器 - MCU 290-350MHz UHF ASK/FSK Transmitter RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube |
| RFPIC12F675KT-I/SS | 功能描述:射频微控制器 - MCU 1 KB Flash FSK ASK RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube |
| RFPMV00 | 制造商:Carlo Gavazzi 功能描述:RSBT ALARM RELAY OUTPUT MODULE |
| RF-PP12/23 | 制造商:Cembre 功能描述:F-CRIMP,BLADE,RED,PP12/23 |
| RFP-QD10 | 功能描述:烙铁 Cartridge Quad PLCC-52 Chip Pkg RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included |
发布紧急采购，3分钟左右您将得到回复。