参数资料
型号: S29JL032J70TFI213
厂商: SPANSION LLC
元件分类: PROM
英文描述: 2M X 16 FLASH 3V PROM, 70 ns, PDSO48
封装: LEAD FREE, MO-142(D)DD, TSOP-48
文件页数: 6/63页
文件大小: 1618K
代理商: S29JL032J70TFI213
14
S29JL032J
S29JL032J_00_05 August 24, 2011
Data
She e t
8.
Device Bus Operations
This section describes the requirements and use of the device bus operations, which are initiated through the
internal command register. The command register itself does not occupy any addressable memory location.
The register is a latch used to store the commands, along with the address and data information needed to
execute the command. The contents of the register serve as inputs to the internal state machine. The state
machine outputs dictate the function of the device. Table 8.1 lists the device bus operations, the inputs and
control levels they require, and the resulting output. The following subsections describe each of these
operations in further detail.
Legend
L = Logic Low = VIL
H = Logic High = VIH
VID = 8.5–12.5V
VHH = 9.0 ± 0.5V
X = Don’t Care
SA = Sector Address
AIN = Address In
DIN = Data In
DOUT = Data Out
Notes:
1. Addresses are A20:A0 in word mode (BYTE# = VIH), A20:A-1 in byte mode (BYTE# = VIL).
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See Boot Sector/Sector Block
3. If WP#/ACC = VIL, the two outermost boot sectors remain protected. If WP#/ACC = VIH, protection on the two outermost boot sectors
depends on whether they were last protected or unprotected using the method described in Boot Sector/Sector Block Protection and
Unprotection on page 23. If WP#/ACC = VHH, all sectors will be unprotected.
8.1
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the
BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ15–DQ0 are active and controlled by CE#
and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ7–DQ0 are
active and controlled by CE# and OE#. The data I/O pins DQ14–DQ8 are tri-stated, and the DQ15 pin is used
as an input for the LSB (A-1) address function. Please note that the BYTE# pin must be connected to either
the system VCC or ground.
Table 8.1 S29JL032J Device Bus Operations
Operation
CE#
OE#
WE#
RESET#
WP#/ACC
Addresses
DQ15–DQ8
DQ7–DQ0
BYTE# = VIH
BYTE# = VIL
Read
L
H
L/H
AIN
DOUT
DQ14–DQ8 = High-Z,
DQ15 = A-1
DOUT
Write
L
H
L
H
AIN
DIN
Standby
VCC ±
0.3V
XX
VCC ±
0.3V
L/H
X
High-Z
Output Disable
L
H
L/H
X
High-Z
Reset
X
L
L/H
X
High-Z
Sector Protect
LH
L
VID
L/H
SA, A6 = L,
A1 = H, A0 = L
XX
DIN
Sector Unprotect
LH
L
VID
SA, A6 = H,
A1 = H, A0 = L
XX
DIN
Temporary Sector
Unprotect
XX
X
VID
AIN
DIN
High-Z
DIN
相关PDF资料
PDF描述
S29PL032J65BFI150 2M X 16 FLASH 3V PROM, 65 ns, PBGA56
S29PL127J70BFI000 8M X 16 FLASH 3V PROM, 70 ns, PBGA80
S29XS064R0PBHW010 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44
S2C3R-1-12-H 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS
S2C5R-1-12-RC 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS
相关代理商/技术参数
参数描述
S29JL032J70TFI220 功能描述:闪存 32MB 闪存 3.0V 70ns Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
S29JL032J70TFI310 功能描述:闪存 32MB 闪存 3.0V 70ns Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
S29JL032J70TFI313 制造商:Spansion 功能描述:
S29JL032J70TFI320 功能描述:闪存 32Mb 3V 70ns Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
S29JL032J70TFI323 功能描述:闪存 32M, 3V, 70ns Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel