收藏本站
参数资料
型号： ST52510F3M6
厂商： STMICROELECTRONICS
元件分类： 微控制器/微处理器
英文描述： MICROCONTROLLER, PDSO20
封装： SOP-20
文件页数： 96/136页
文件大小： 3335K
代理商： ST52510F3M6
Obsolete
Product(s)
- Obsolete
Product(s)
ST52510xx ST52513xx
62/136
9 INSTRUCTION SET
ST52F510/F513 supplies 107 (98 + 9 Fuzzy)
instructions that perform computations and control
the device. Computational time required for each
instruction consists of one clock pulse for each
Cycle plus 2 clock pulses for the decoding phase.
Total computation time for each instruction is
reported in Table 9.1
The ALU of ST52F510/F513 can perform
multiplication
(MULT)
and
division
(DIV).
Multiplication is performed by using 8 bit operands
storing the result in 2 registers (16 bit values), see
Figure 2.3.
Division is performed between a 16 bit dividend
and an 8 bit divider, the result and the remainder
are stored in two 8-bit registers (see Figure 2.4).
9.1 Addressing Modes
ST52F510/F513 instructions allow the following
addressing modes:
■ Inherent: this instruction type does not require
an operand because the opcode specifies all the
information necessary to carry out the
instruction. Examples: NOP, SCF.
■ Immediate: these instructions have an operand
as a source immediate value. Examples: LDRC,
ADDI.
■ Direct: the operands of these instructions are
specified with the direct addresses. The
operands can refer (according to the opcode) to
addresses belonging to the different addressing
spaces. Example: SUB, LDRE.
■ Indirect: data addresses that are required are
found in the locations specified as operands.
Both source and/or destination operands can be
addressed indirectly. The operands can refer,
(according to the opcode) to addresses
belonging to different addressing spaces.
Examples: LDRR(reg1),(reg2);
LDER mem_addr,(reg1).
■ Bit Direct: operands of these instructions directly
address the bits of the specified Register File
locations. Examples: BSET, BTEST.
9.2 Instruction Types
ST52F510/F513 supplies the following instruction
types:
■ Load Instructions
■ Arithmetic and Logic Instructions
■ Bitwise instructions
■ Jump Instructions
■ Interrupt Management Instructions
■ Control Instructions
The instructions are listed in Table 9.1
Table 9.1 Instruction Set
Load Instructions
Mnemonic
Instruction
Bytes
Cycles
Z
S
C
BLKSET
BLKSET const
2
(*)
-
GETPG
GETPG regx
2
7
-
LDCE
LDCE confx,memy
3
8/10
-
LDCI
LDCI confx, const
3
7
-
LDCNF
LDCNF regx, conf
3
7
-
LDCR
LDCR confx, regy
3
8
-
LDER
LDER memx, regy
3
11
-
LDER
LDER (regx),(regy)
3
12
-
LDER
LDER (regx), regy
3
11
-
LDER
LDER memx,(regy)
3
12
-
LDFR
LDFR fuzzyx, regy
3
8
-
相关PDF资料
PDF描述
ST52E430B/D 8-BIT, UVPROM, 20 MHz, MICROCONTROLLER, CDIP32
ST52F510F1M6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO20
ST52F510G0B6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP28
ST52F513F0M6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO20
ST52F513F1B6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP20
相关代理商/技术参数
参数描述
ST52510G2 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH
ST52510G3 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH
ST52510K2 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH
ST52510K3 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH
ST52510Y2 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*