- 您现在的位置：买卖IC网 > PDF目录383877 > T9000 (Lineage Power) ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) PDF资料下载
参数资料
| 型号： | T9000 |
| 厂商： | Lineage Power |
| 英文描述： | ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) |
| 中文描述： | ISDN网络终端节点（新界西）设备（ISDN网网络终端节点器件） |
| 文件页数： | 54/126页 |
| 文件大小： | 1523K |
| 代理商： | T9000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页
54
Lucent Technologies Inc.
Advance Data Sheet
April 2000
ISDN Network Termination Node (NTN) Device
T9000
9 HDLC with FIFO Module
(continued)
9.3 HDLC Receiver
Downstream D channel is always transferred to the
HDLC receiver. The HDLC receiver removes flags,
does zero bit deletion, and calculates the FCS for the
downstream D-channel information. Deframed data is
converted from serial to parallel (byte delimited) and
passed to the microcontroller through the receiver
FIFO HRX register.
9.3.1 HDLC Receiver Initialization
On powerup, the HDLC receiver is initialized automati-
cally. After powerup, whenever there is any change to
the HRCF[DROPCRC], HRCF[RXMODE],
HRCF[BAE], or HSM0[BAP(7:0)] configuration bits, the
bit HRCF[RX_INIT] needs to be set to 1 to reinitialize
the HDLC receiver. Once the initialization is completed,
the HRCF[RX_INIT] bit automatically returns to 0.
During initialization, register bit HRCF[DROPCRC] is
sampled. If it is one (the default), the FCS will be
dropped (not stored in the receiver FIFO). If
HRCF[DROPCRC] = 0, the complete deframed packet,
including its FCS, will be stored in the receiver FIFO.
If the device is programmed for address matching, then
prior to storing a packet in the receiver FIFO, its
address is checked against a set of patterns (see Sec-
tion 9.4, Address Recognition). Only packets with an
address field matching one of the programmed
address values are transferred to the receiver FIFO, all
others are rejected. At the end of a frame, a status byte
is transferred to the HDLC receiver FIFO that provides
information about the following events: frame-overrun,
frame-complete, frame-error, and frame-abort.
Figure 10 shows the structure of the status byte. Each
bit is set to one when the corresponding condition is
active.
Bit 7 (OVR).
The overrun bit indicates that the frame
has been closed by a receive FIFO overrun condition
(see section 9.3.1.1 Overrun Condition ).
Bit 6 (EOF).
The end of frame bit indicates that the
packet has been properly terminated with a closing
flag.
Bit 5 (FERR).
The FCS error bit indicates that the
results of comparing the incoming FCS with internally
calculated FCS on the received data (according to the
ITU CRC-16 polynomial) did not match.
Bit 4 (FABRT).
The frame abort bit indicates that the
frame has been closed with an abort pattern
(01111111).
Bits 2—0 (CBIT).
The check error bit provides an extra
error check. In most HDLC based protocols, the packet
length is an exact multiple number of bytes. When this
is the case, CBIT = 111. Otherwise, CBIT
≠
111.
The above definitions for the status bits imply that cor-
rectly received frames will have 47h as the status byte.
Bit 3 is reserved and is set to 0.
Figure 10. HDLC Receiver Status Word
Multiple packets may be stored in the receiver FIFO at
a given time. The HRDA[NBNSW] register bits indicate
the number of bytes until the next status word in the
FIFO. If there are no status words in the FIFO, it indi-
cates the numbers of bytes of an unfinished packet cur-
rently stored into the FIFO.
Packets less than 2 bytes in length (4 bytes if
HRCF[DROPCRC] = 1) are automatically rejected.
7
6
5
4
3
—
2:0
CBIT
OVR
EOF
FERR
FABRT
相关PDF资料 |
PDF描述 |
|---|---|
| T90RIA10 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA40 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA60 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA80 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA100 | MEDIUM POWER PHASE CONTROL THYRISTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| T9001 | 功能描述:罩类、盒类及壳类产品 15x14x3-1/2(3.13cf) 1 Compartment RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9006 | 功能描述:罩类、盒类及壳类产品 15 x 14 x 3-1/2 (2.96cf) RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9007 | 功能描述:罩类、盒类及壳类产品 13 1/8 x 13 1/8 x 3" 6 COMPARTMENTS RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9008 | 制造商:Nortools International Ltd 功能描述:HSS METRIC DIE SET,M3-M12 |
| T900BK | 功能描述:罩类、盒类及壳类产品 of Box Dividers Clear RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
发布紧急采购，3分钟左右您将得到回复。