- 您现在的位置：买卖IC网 > PDF目录383877 > T9000 (Lineage Power) ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) PDF资料下载
参数资料
| 型号： | T9000 |
| 厂商： | Lineage Power |
| 英文描述： | ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) |
| 中文描述： | ISDN网络终端节点（新界西）设备（ISDN网网络终端节点器件） |
| 文件页数： | 73/126页 |
| 文件大小： | 1523K |
| 代理商： | T9000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页当前第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页
Lucent Technologies Inc.
73
Advance Data Sheet
April 2000
ISDN Network Termination Node (NTN) Device
T9000
10 GCI+ Interface Module
(continued)
10.2 GCI Modes (GCCF[GMODE(1:0)] = 0x)
GCI mode is for use with codecs having a GCI inter-
face. Two GCI modes are supported by the NTN
device:
I
GCI-NT mode with a GCI frame structure of only one
GCI channel.
I
GCI-SCIT mode with a GCI frame structure of three
GCI channels.
In both modes, the circuit operates as a GCI master
device, i.e., the DCL output pin provides the GCI clock
signal (512 kHz or 1536 kHz). A BCLK signal is avail-
able on the GPIO2.1 pin when GPAF1[GPAF2.1] = 1.
BCLK occurs once per bit time and is a divide-by-two
version of the DCL signal.
The FS1 output pin provides the frame synchronization
clock (FSC) signal as defined by the GCI standard (see
Figure 17). The internal PFS1 and PFS2 signals mark
the location of the B1 and B2 time slots on the TDM
highway. PFS2 is output on the FS2 pin (see Table 77).
PFS1 can be made available on the GPIO2.2 pin by
setting GPAF1[GPAF2.2] = 1.
The PFS1 and PFS2 (programmable frame sync) sig-
nals may be programmed to be a pulse (duration of
one bit period, sometimes referred to as short frame
sync) or envelope (duration of one time slot, some-
times referred to as long frame sync). Register bit
GCCF[PFSPE] sets the short or long frame sync mode.
The U-interface B1 and B2 channels are normally
transferred to/from the codec on the time slots marked
by PFS1 and PFS2, respectively. This ordering can be
switched by setting the DFAC[BSWAP] register bit to 1.
Register bit GCCF[PFSDEL] controls the relative
delay between PFSx (x = 1 or x = 2) and the first
data bit of the time slot associated with PFSx. When
GCCF[PFSDEL] = 0, the PFSx rising edge is coinci-
dent with the start of the first data bit of the correspond-
ing time slot. When GCCF[PFSDEL] = 1, the PFSx
rising edge occurs one data bit prior to the first data bit
of the corresponding time slot.
Generation of the PFSx signals and data transfer
to/from the corresponding time slots may be disabled
by setting DFR[PFSx_ACT] = 0.
10.3 GCI-NT Mode (GCCF[GMODE(1:0)] = 00)
Figure 16 shows the frame structure for the GCI-NT
mode. The DCL clock rate is automatically set to
512 kHz, overriding the value defined by
GCCF[GRATE(1:0)]. In addition, a powerdown mode is
available in which DCL is stopped (see Section 10.5,
GCI+ Powerdown Mode).
The data rate in GCI-NT mode is automatically set to
256 kHz, overriding the value defined by
GCCF[CKMODE]. A total of four 8-bit time slots are
contained in each frame. Time slots 0 and 1 carry user
data, time slot 2 is the GCI monitor (MON) channel,
and time slot 3 is the GCI signaling and control chan-
nel.
The FS1 output pin provides the frame synchronization
clock (FSC) as defined by the GCI standard. It
becomes active with the rising edge of DCL at the start
of time slot 0 and is turned off one-half of a DCL period
prior to the start of time slot 1.
In this mode, the NTN device:
I
May transfer upstream/downstream data on time-
slots 0 and 1.
I
Manages the MON channel’s operation, mainte-
nance, and data transfer (see Section 10.3.2, Moni-
tor Message Transfer for more details).
I
Provides control of the C/I subchannel (see Section
10.4, C/I Message Transfer for more details).
Register bit GCOF1[OFF10] controls the time slots to
which PFS1 and PFS2 are associated. If
GCOF1[OFF10] = 0 PFS1 occurs during time slot 0
(GCI-B1 channel) and PFS2 occurs during time slot 1
(GCI-B2 channel). If GCOF1[OFF10] = 1 the associa-
tion is reversed, PFS1 occurs during time slot 1
(GCI-B2 channel) and the PFS2 occurs during time slot
0 (GCI-B1 channel). Note that the GCOF1(OFF1[4:1])
bits are ignored in GCI-NT mode, as is the entire
GCOF2 register.
相关PDF资料 |
PDF描述 |
|---|---|
| T90RIA10 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA40 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA60 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA80 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA100 | MEDIUM POWER PHASE CONTROL THYRISTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| T9001 | 功能描述:罩类、盒类及壳类产品 15x14x3-1/2(3.13cf) 1 Compartment RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9006 | 功能描述:罩类、盒类及壳类产品 15 x 14 x 3-1/2 (2.96cf) RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9007 | 功能描述:罩类、盒类及壳类产品 13 1/8 x 13 1/8 x 3" 6 COMPARTMENTS RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9008 | 制造商:Nortools International Ltd 功能描述:HSS METRIC DIE SET,M3-M12 |
| T900BK | 功能描述:罩类、盒类及壳类产品 of Box Dividers Clear RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
发布紧急采购，3分钟左右您将得到回复。