- 您现在的位置：买卖IC网 > PDF目录383877 > T9000 (Lineage Power) ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) PDF资料下载
参数资料
| 型号： | T9000 |
| 厂商： | Lineage Power |
| 英文描述： | ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) |
| 中文描述： | ISDN网络终端节点（新界西）设备（ISDN网网络终端节点器件） |
| 文件页数： | 77/126页 |
| 文件大小： | 1523K |
| 代理商： | T9000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页当前第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页
Lucent Technologies Inc.
77
Advance Data Sheet
April 2000
ISDN Network Termination Node (NTN) Device
T9000
10 GCI+ Interface Module
(continued)
10.3 GCI-NT Mode (GCCF[GMODE(1:0)] = 00)
(continued)
10.3.2 Monitor Message Transfer
For both GCI-NT and GCI-TE modes, the NTN man-
ages the monitor channel (MON) protocol as defined
by the GCI standard. In GCI-NT mode, monitor data
transfer occurs in time slot 2 (MON-0) using the A&E
bit pair in time slot 3. In GCI-TE mode, monitor data
transfer occurs in time slot 6 (MON-1) using the A&E
bit pair in time slot 7.
Monitor messages may be one or more bytes in length.
To transmit a single byte message downstream, the
microcontroller writes the monitor byte into the GCDML
register. Once this byte is internally loaded, the GCI-
controller asserts the interrupt bit GCIR[DMRDY] indi-
cating to the microcontroller that it is ready to accept a
new message to be transmitted. If the transmission is
successfully completed, the GCI controller asserts
interrupt bit GCIR[DMEOM]. Otherwise, if the transmis-
sion has been aborted, it will assert interrupt bit
GCIR(DMABRT). Downstream monitor message
aborts may occur as a consequence of an abort
request by the downstream device or an expiration of
the GCI controller downstream timer (if
GCOF1[GTMODE] = 1).
Multibyte monitor messages operate in a similar man-
ner to single-byte messages, except that for an N-byte
message, bytes 1 to N – 1 are written into register
GCDMD, and the last monitor byte is written into regis-
ter GCDML. The interrupt bit GCIR[DMRDY] is used in
both cases to signify when new downstream data may
be written to either GCDMD or GCDML.
Upstream monitor bytes, when confirmed, are trans-
ferred to the GCUMD register. Interrupt bit
GCIR[UMRDY] is asserted to indicate a new monitor
byte has been successfully received. At the completion
of an upstream message, interrupt bit GCIR[UMEOM]
is asserted. If the upstream message is aborted, the
interrupt bit GCIR [UMABRT] is asserted. Upstream
monitor message aborts may occur as a consequence
of an implicit abort produced by an invalid upstream
A&E bit pair sequence (normally produced by the
downstream device) or an expiration of the GCI con-
troller upstream timer (if GCOF1[GTMODE] = 1).
The embedded GCI controller has one timer associ-
ated with each monitor direction to avoid deadlock situ-
ations. Both timers may be enabled by setting
GCOF1[GTMODE] = 1. The downstream timer will be
started each time the transfer of a downstream monitor
byte is initiated. If the byte is not acknowledged within
four frames, the timer will expire and generate an abort
request. The upstream timer will be started upon the
detection of a new byte. If this byte is not confirmed by
the far end (because it did not detect identical bytes in
two consecutive frames—upstream RNR event) or the
byte cannot be transferred to the GCUMD register
(because the microcontroller has not yet read the previ-
ous byte—upstream RNR event), the timer will expire.
10.4 C/I Message Transfer
For both GCI-NT and GCI-TE modes, the NTN man-
ages data transfer over the command/indication chan-
nel as defined by the GCI standard. In GCI-NT mode,
C/I data transfer occurs in the first 6 bits of time slot 3
(C/I-0). In GCI-TE mode, C/I data transfer occurs in the
first 6 bits of time slot 7 (C/I-1).
To transmit a downstream C/I code, the microcontroller
writes the code into the GCDCI register. This code will
be continuously transmitted until a new code is written
to GCDCI. The internal GCI controller will not read the
new code from GCDCI until the current code has been
transferred in at least two consecutive frames.
Upstream command/indication codes are first filtered
before they are transferred to the GCUCI register. A
double last look criterion is used to validate a new C/I
code, i.e., a new code is transferred to the GCUCI reg-
ister only if it is different from the previously loaded
value and is received in two consecutive GCI frames.
Whenever this happens, the GCIR[UCIC] interrupt is
asserted.
10.5 GCI+ Powerdown Mode
The GCI+ may be placed in a powerdown mode by set-
ting GCCF[GRATE(1:0)] = 00). Prior to enabling power-
down mode, the user must set DFR[PFS1_ACT] = 0
and DFR[PFS2_ACT] = 0. While in powerdown mode,
the DCL clock signal is stopped (held low), the PFS1
and PFS2 signals are held low, and the DD signal is
3-stated.
When in powerdown, a falling edge on the DU signal
causes an assertion of the interrupt bit GCIR[GWUP].
This allows the user to write a powerup routine for the
GCI+ interface.
相关PDF资料 |
PDF描述 |
|---|---|
| T90RIA10 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA40 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA60 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA80 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA100 | MEDIUM POWER PHASE CONTROL THYRISTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| T9001 | 功能描述:罩类、盒类及壳类产品 15x14x3-1/2(3.13cf) 1 Compartment RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9006 | 功能描述:罩类、盒类及壳类产品 15 x 14 x 3-1/2 (2.96cf) RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9007 | 功能描述:罩类、盒类及壳类产品 13 1/8 x 13 1/8 x 3" 6 COMPARTMENTS RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9008 | 制造商:Nortools International Ltd 功能描述:HSS METRIC DIE SET,M3-M12 |
| T900BK | 功能描述:罩类、盒类及壳类产品 of Box Dividers Clear RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
发布紧急采购，3分钟左右您将得到回复。