- 您现在的位置：买卖IC网 > PDF目录383877 > T9000 (Lineage Power) ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) PDF资料下载
参数资料
| 型号： | T9000 |
| 厂商： | Lineage Power |
| 英文描述： | ISDN Network Termination Node (NTN) Device(ISDN网络终端节点器件) |
| 中文描述： | ISDN网络终端节点（新界西）设备（ISDN网网络终端节点器件） |
| 文件页数： | 56/126页 |
| 文件大小： | 1523K |
| 代理商： | T9000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页当前第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页
56
Lucent Technologies Inc.
Advance Data Sheet
April 2000
ISDN Network Termination Node (NTN) Device
T9000
9 HDLC with FIFO Module
(continued)
9.3 HDLC Receiver
(continued)
9.3.1 HDLC Receiver Initialization
(continued)
Up to 16 status bytes can be stored in the receiver
FIFO at a given time. Once this condition is reached, it
is indicated by assertion of the HIR[RSTF] interrupt
register bit and the FIFO is considered full. In the worst
case, the microcontroller has approximately 2 ms from
the time HIR[RSTF] is asserted to read data from the
FIFO and avoid overrun errors (an overrun error is indi-
cated by assertion of the HIR[ROVR] interrupt bit).
When a status word with its EOF bit set is loaded into
the FIFO, interrupt bit HIR[REOF] is set. Similarly,
when a status word with its ABRT bit set is loaded into
the FIFO, interrupt bit HIR[RABT] is set.
When the receive FIFO is filled at or above the level
programmed in register HRTH, an interrupt is asserted
by enabling the bit HIR[RTHR]. The interrupt should
clear when the interrupt status register is read, and
should not be asserted again until the receive FIFO is
emptied to the point that more spaces remain in the
FIFO than the value programmed in the HRTH register,
and then enough bytes are received to again cause the
delay FIFO fill level to reach the HRTH register value.
9.3.1.1 Overrun Condition
An overrun condition occurs when the receiver is
unable to download a processed byte into the FIFO
because the FIFO is full or contains 16 status words.
Interrupt bit HIR[ROVR] is set when an overrun occurs.
If the overrun condition occurs during the reception of a
packet with a matching address field, the current frame
will be closed and its status word’s OVR bit will be set.
The remainder of the frame will be dropped even if the
overrun condition has been removed. The receiver
must be reinitialized after the overrun condition, before
new packets can be properly received.
9.4 Address Recognition
A very flexible address comparison scheme is imple-
mented in the NTN device. Eight registers are used for
storing SAPI or TEI patterns for comparison with the
incoming address. The registers are grouped logically
into the pairs HSM0/HTM0, HSM1/HTM1, HSM2/
HTM2, HSM3/HTM3 to define a total of four DLCI (data
link connection identifier) address matching patterns. If
HSMOD and HTMOD are programmed for address
matching, only frames with an address field matching
one of the programmed address values (or special
addresses) are transferred to the receive FIFO. All oth-
ers are ignored. If an address match occurs, the
address field is also loaded into the HDLC receive
FIFO.
The address modifier registers, HSMOD and HTMOD,
are used to control the address recognition modes and
can be used to extend the DLCIs defined in the four
HSMx/HTMx register pairs. Figure 12 shows an exam-
ple of this for the SAPI0/TEI0 pair (i.e., bits
SAPI0M[1:0] and TEI0M[1:0] in HSMOD and HTMOD,
respectively).
Consider the default setting of TEI0M = 00 and
SAPI0M = 00 on powerup. In this case, TEIM0 = 00
causes rejection of all packets for a given DLCI pair,
independent of the state of SAPI0M. This means that
on powerup, the HDLC receiver is disabled and will not
receive any packets. Now consider the effect of setting
TEI0M to the other three possible values while leaving
SAPI0M set to 00.
Setting TEI0M = 01 enables the recognition of the
DLCI0 address programmed in the HSM0/HTM0 pair.
Setting TEI0M = 10 extends the definition of DLCI0 to
include the broadcast TEI value, 127. Setting TEI0M =
11 extends the definition of DLCI0 to include all TEI val-
ues.
In a similar way, setting SAPI0M to the values 01, 10,
or 11 will extend the existing definition of DLCI0 to
include SAPI0 = 0, SAPI = 63, or all SAPI values,
respectively. Note, then, that when SAPI0M/TEI0M =
1111, any packet more than 2 bytes in length (4 bytes if
HRCF[DROPCRC] = 1) will be downloaded to the
receiver FIFO, regardless of its address. This effec-
tively disables address recognition for all four DLCI
pairs, since the values programmed into the other three
pairs become irrelevant in this case.
One further level of address recognition control is avail-
able via the HSCR register, which provides a means for
enabling/disabling comparison of the command
response (C/R) bit for each SAPI. When
HSCR[SxCRE] = 0, no comparison is done on the C/R
bit of the SAPI defined by HSMx register. When
HSCR[SXCRE] = 1, the C/R bit is included in compari-
son. However, for extended SAPI values of 0 or 63
(HSMOD[SAPIxM] = 01 or = 10), no comparison is ever
done on the C/R bit.
In the transmit direction, no automatic address inser-
tion is performed.
相关PDF资料 |
PDF描述 |
|---|---|
| T90RIA10 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA40 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA60 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA80 | MEDIUM POWER PHASE CONTROL THYRISTORS |
| T90RIA100 | MEDIUM POWER PHASE CONTROL THYRISTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| T9001 | 功能描述:罩类、盒类及壳类产品 15x14x3-1/2(3.13cf) 1 Compartment RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9006 | 功能描述:罩类、盒类及壳类产品 15 x 14 x 3-1/2 (2.96cf) RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9007 | 功能描述:罩类、盒类及壳类产品 13 1/8 x 13 1/8 x 3" 6 COMPARTMENTS RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| T9008 | 制造商:Nortools International Ltd 功能描述:HSS METRIC DIE SET,M3-M12 |
| T900BK | 功能描述:罩类、盒类及壳类产品 of Box Dividers Clear RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
发布紧急采购，3分钟左右您将得到回复。