- 您现在的位置：买卖IC网 > PDF目录17007 > USB-I2C/LIN-CONV-Z (Analog Devices Inc)USB TO I2C/LIN CONV BOARD PDF资料下载
参数资料
| 型号： | USB-I2C/LIN-CONV-Z |
| 厂商： | Analog Devices Inc |
| 文件页数： | 49/104页 |
| 文件大小： | 0K |
| 描述： | USB TO I2C/LIN CONV BOARD |
| 标准包装： | 1 |
| 附件类型： | 适配器板 |
| 适用于相关产品： | ARM7TDMI? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页当前第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
Data Sheet
ADuC7019/20/21/22/24/25/26/27/28/29
Rev. F | Page 49 of 104
Pseudo Differential Mode
In pseudo differential mode, Channel is linked to the VIN pin
of the ADuC7019/20/21/22/24/25/26/27/28/29. SW2 switches
between A (Channel) and B (VREF). The VIN pin must be
connected to ground or a low voltage. The input signal on VIN+
can then vary from VIN to VREF + VIN. Note that VIN must be
chosen so that VREF + VIN does not exceed AVDD.
04955-
019
CAPACITIVE
DAC
CAPACITIVE
DAC
CONTROL
LOGIC
COMPARATOR
SW3
SW1
A
B
SW2
CS
VREF
AIN0
AIN11
VIN–
MUX
CHANNEL+
CHANNEL–
Figure 56. ADC in Pseudo Differential Mode
Single-Ended Mode
In single-ended mode, SW2 is always connected internally to
ground. The VIN pin can be floating. The input signal range on
VIN+ is 0 V to VREF.
04955-
020
CAPACITIVE
DAC
CAPACITIVE
DAC
CONTROL
LOGIC
COMPARATOR
SW3
SW1
A
B
CS
AIN0
AIN11
MUX
CHANNEL+
CHANNEL–
Figure 57. ADC in Single-Ended Mode
Analog Input Structure
Figure 58 shows the equivalent circuit of the analog input structure
of the ADC. The four diodes provide ESD protection for the analog
inputs. Care must be taken to ensure that the analog input
signals never exceed the supply rails by more than 300 mV;
exceeding 300 mV causes these diodes to become forward-
biased and start conducting into the substrate. These diodes can
conduct up to 10 mA without causing irreversible damage to
the part.
The C1 capacitors in Figure 58 are typically 4 pF and can be
primarily attributed to pin capacitance. The resistors are
lumped components made up of the on resistance of the
switches. The value of these resistors is typically about 100 Ω.
The C2 capacitors are the ADC’s sampling capacitors and
typically have a capacitance of 16 pF.
AVDD
C1
D
R1 C2
AVDD
C1
D
R1 C2
04
95
5-
0
21
Figure 58. Equivalent Analog Input Circuit Conversion Phase: Switches Open,
Track Phase: Switches Closed
For ac applications, removing high frequency components from
the analog input signal is recommended by using an RC low-
pass filter on the relevant analog input pins. In applications
where harmonic distortion and signal-to-noise ratio are critical,
the analog input should be driven from a low impedance
source. Large source impedances significantly affect the ac
performance of the ADC. This can necessitate the use of an
input buffer amplifier. The choice of the op amp is a function of
the particular application. Figure 59 and Figure 60 give an
example of an ADC front end.
04
95
5-
061
ADuC7019/
ADuC702x
ADC0
10
0.01F
Figure 59. Buffering Single-Ended/Pseudo Differential Input
04
95
5-
06
2
ADuC7019/
ADuC702x
ADC0
VREF
ADC1
Figure 60. Buffering Differential Inputs
When no amplifier is used to drive the analog input, the source
impedance should be limited to values lower than 1 kΩ. The
maximum source impedance depends on the amount of total
harmonic distortion (THD) that can be tolerated. The THD
increases as the source impedance increases and the performance
degrades.
DRIVING THE ANALOG INPUTS
Internal or external references can be used for the ADC. In
the differential mode of operation, there are restrictions on the
common-mode input signal (VCM), which is dependent upon
the reference value and supply voltage used to ensure that the
signal remains within the supply rails. Table 28 gives some
calculated VCM minimum and VCM maximum values.
相关PDF资料 |
PDF描述 |
|---|---|
| HBM10DSEI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| EBC35DCSD-S288 | CONN EDGECARD 70POS .100 EXTEND |
| HBM15DRYN-S13 | CONN EDGECARD 30POS .156 EXTEND |
| RBC17DRES-S13 | CONN EDGECARD 34POS .100 EXTEND |
| HBM15DRYH-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USB-I2C-SS | 功能描述:USB 接口集成电路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| USB-ICP-80C51ISP | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC2K | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC9XX | 功能描述:程序设计器 - 基于处理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-SAB9 | 功能描述:插座和适配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
发布紧急采购，3分钟左右您将得到回复。