- 您现在的位置：买卖IC网 > PDF目录17007 > USB-I2C/LIN-CONV-Z (Analog Devices Inc)USB TO I2C/LIN CONV BOARD PDF资料下载
参数资料
| 型号： | USB-I2C/LIN-CONV-Z |
| 厂商： | Analog Devices Inc |
| 文件页数： | 87/104页 |
| 文件大小： | 0K |
| 描述： | USB TO I2C/LIN CONV BOARD |
| 标准包装： | 1 |
| 附件类型： | 适配器板 |
| 适用于相关产品： | ARM7TDMI? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页当前第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
Data Sheet
ADuC7019/20/21/22/24/25/26/27/28/29
Rev. F | Page 83 of 104
PROCESSOR REFERENCE PERIPHERALS
INTERRUPT SYSTEM
There are 23 interrupt sources on the ADuC7019/20/21/22/
24/25/26/27/28/29 that are controlled by the interrupt
controller. Most interrupts are generated from the on-chip
peripherals, such as ADC and UART. Four additional interrupt
sources are generated from external interrupt request pins,
IRQ0, IRQ1, IRQ2, and IRQ3. The ARM7TDMI CPU core only
recognizes interrupts as one of two types: a normal interrupt
request IRQ or a fast interrupt request FIQ. All the interrupts
can be masked separately.
The control and configuration of the interrupt system are
managed through nine interrupt-related registers, four
dedicated to IRQ, and four dedicated to FIQ. An additional
MMR is used to select the programmed interrupt source. The
bits in each IRQ and FIQ register (except for Bit 23) represent
the same interrupt source as described in Table 160.
Table 160. IRQ/FIQ MMRs Bit Description
Bit
Description
0
All interrupts OR’ed (FIQ only)
1
SWI
2
Timer0
3
Timer1
4
Wake-up timer (Timer2)
5
Watchdog timer (Timer3)
6
Flash control
7
ADC channel
8
PLL lock
9
I2C0 slave
10
I2C0 master
11
I2C1 master
12
SPI slave
13
SPI master
14
UART
15
External IRQ0
16
Comparator
17
PSM
18
External IRQ1
19
PLA IRQ0
20
PLA IRQ1
21
External IRQ2
22
External IRQ3
23
PWM trip (IRQ only)/PWM sync (FIQ only)
IRQ
The interrupt request (IRQ) is the exception signal to enter the
IRQ mode of the processor. It is used to service general-purpose
interrupt handling of internal and external events.
The four 32-bit registers dedicated to IRQ are IRQSTA,
IRQSIG, IRQEN, and IRQCLR.
Table 161. IRQSTA Register
Name
Address
Default Value
Access
IRQSTA
0xFFFF0000
0x00000000
R
IRQSTA (read-only register) provides the current-enabled IRQ
source status. When set to 1, that source should generate an
active IRQ request to the ARM7TDMI core. There is no priority
encoder or interrupt vector generation. This function is
implemented in software in a common interrupt handler
routine. All 32 bits are logically OR’ed to create the IRQ signal
to the ARM7TDMI core.
Table 162. IRQSIG Register
Name
Address
Default Value
Access
IRQSIG
0xFFFF0004
0x00XXX0001
R
1
X indicates an undefined value.
IRQSIG reflects the status of the different IRQ sources. If a periph-
eral generates an IRQ signal, the corresponding bit in the IRQSIG
is set; otherwise, it is cleared. The IRQSIG bits are cleared when
the interrupt in the particular peripheral is cleared. All IRQ
sources can be masked in the IRQEN MMR. IRQSIG is read only.
Table 163. IRQEN Register
Name
Address
Default Value
Access
IRQEN
0xFFFF0008
0x00000000
R/W
IRQEN provides the value of the current enable mask. When
each bit is set to 1, the source request is enabled to create an
IRQ exception. When each bit is set to 0, the source request is
disabled or masked, which does not create an IRQ exception.
Note that to clear an already enabled interrupt source, the user
must set the appropriate bit in the IRQCLR register. Clearing an
interrupt’s IRQEN bit does not disable the interrupt.
Table 164. IRQCLR Register
Name
Address
Default Value
Access
IRQCLR
0xFFFF000C
0x00000000
W
IRQCLR (write-only register) clears the IRQEN register in
order to mask an interrupt source. Each bit set to 1 clears the
corresponding bit in the IRQEN register without affecting the
remaining bits. The pair of registers, IRQEN and IRQCLR,
independently manipulates the enable mask without requiring
an atomic read-modify-write.
相关PDF资料 |
PDF描述 |
|---|---|
| HBM10DSEI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| EBC35DCSD-S288 | CONN EDGECARD 70POS .100 EXTEND |
| HBM15DRYN-S13 | CONN EDGECARD 30POS .156 EXTEND |
| RBC17DRES-S13 | CONN EDGECARD 34POS .100 EXTEND |
| HBM15DRYH-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USB-I2C-SS | 功能描述:USB 接口集成电路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| USB-ICP-80C51ISP | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC2K | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC9XX | 功能描述:程序设计器 - 基于处理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-SAB9 | 功能描述:插座和适配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
发布紧急采购，3分钟左右您将得到回复。