- 您现在的位置：买卖IC网 > PDF目录17007 > USB-I2C/LIN-CONV-Z (Analog Devices Inc)USB TO I2C/LIN CONV BOARD PDF资料下载
参数资料
| 型号： | USB-I2C/LIN-CONV-Z |
| 厂商： | Analog Devices Inc |
| 文件页数： | 68/104页 |
| 文件大小： | 0K |
| 描述： | USB TO I2C/LIN CONV BOARD |
| 标准包装： | 1 |
| 附件类型： | 适配器板 |
| 适用于相关产品： | ARM7TDMI? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页当前第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 66 of 104
The GDCLK value can range from 0 to 255, corresponding to a
programmable chopping frequency rate of 40.8 kHz to 10.44 MHz
for a 41.78 MHz core frequency. The gate drive features must be
programmed before operation of the PWM controller and are
typically not changed during normal operation of the PWM
controller. Following a reset, all bits of the PWMCFG register
are cleared so that high frequency chopping is disabled, by default.
0
49
55
-03
1
PWMCH0
PWMDAT0
0L
0H
2 × PWMDAT1
4 × (GDCLK + 1) ×
tCORE
2 × PWMDAT1
Figure 72. Typical PWM Signals with High Frequency Gate Chopping
Enabled on Both High-Side and Low-Side Switches
PWM Shutdown
In the event of external fault conditions, it is essential that the
PWM system be instantaneously shut down in a safe fashion. A
low level on the PWMTRIP pin provides an instantaneous,
asynchronous (independent of the MicroConverter core clock)
shutdown of the PWM controller. All six PWM outputs are
placed in the off state, that is, in low state. In addition, the
PWMSYNC pulse is disabled. The PWMTRIP pin has an internal
pull-down resistor to disable the PWM if the pin becomes
disconnected. The state of the PWMTRIP pin can be read from
Bit 3 of the PWMSTA register.
If a PWM shutdown command occurs, a PWMTRIP interrupt is
generated, and internal timing of the 3-phase timing unit of the
PWM controller is stopped. Following a PWM shutdown, the
PWM can be reenabled (in a PWMTRIP interrupt service
routine, for example) only by writing to all of the PWMDAT0,
PWMCH0, PWMCH1, and PWMCH2 registers. Provided that
the external fault is cleared and the PWMTRIP is returned to a
high level, the internal timing of the 3-phase timing unit
resumes, and new duty-cycle values are latched on the next
PWMSYNC boundary.
Note that the PWMTRIP interrupt is available in IRQ only,
and the PWMSYNC interrupt is available in FIQ only. Both
interrupts share the same bit in the interrupt controller.
Therefore, only one of the interrupts can be used at a time.
See the Interrupt System section for further details.
PWM MMRs Interface
The PWM block is controlled via the MMRs described in
this section.
Table 66. PWMCON Register
Name
Address
Default Value
Access
PWMCON
0xFFFFFC00
0x0000
R/W
PWMCON is a control register that enables the PWM and
chooses the update rate.
Table 67. PWMCON MMR Bit Descriptions
Bit
Name
Description
7:5
Reserved.
4
PWM_SYNCSEL
External sync select. Set to use external
sync. Cleared to use internal sync.
3
PWM_EXTSYNC
External sync select. Set to select
external synchronous sync signal.
Cleared for asynchronous sync signal.
2
PWMDBL
Double update mode. Set to 1 by user
to enable double update mode.
Cleared to 0 by the user to enable
single update mode.
1
PWM_SYNC_EN
PWM synchronization enable. Set by
user to enable synchronization. Cleared
by user to disable synchronization.
0
PWMEN
PWM enable bit. Set to 1 by user to
enable the PWM. Cleared to 0 by user
to disable the PWM. Also cleared
automatically with PWMTRIP
(PWMSTA MMR).
Table 68. PWMSTA Register
Name
Address
Default Value
Access
PWMSTA
0xFFFFFC04
0x0000
R/W
PWMSTA reflects the status of the PWM.
Table 69. PWMSTA MMR Bit Descriptions
Bit
Name
Description
15:10
Reserved.
9
PWMSYNCINT
PWM sync interrupt bit. Writing a 1 to
this bit clears this interrupt.
8
PWMTRIPINT
PWM trip interrupt bit. Writing a 1 to
this bit clears this interrupt.
3
PWMTRIP
Raw signal from the PWMTRIP pin.
2:1
Reserved.
0
PWMPHASE
PWM phase bit. Set to 1 by the Micro-
Converter when the timer is counting
down (first half). Cleared to 0 by the
MicroConverter when the timer is
counting up (second half).
相关PDF资料 |
PDF描述 |
|---|---|
| HBM10DSEI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| EBC35DCSD-S288 | CONN EDGECARD 70POS .100 EXTEND |
| HBM15DRYN-S13 | CONN EDGECARD 30POS .156 EXTEND |
| RBC17DRES-S13 | CONN EDGECARD 34POS .100 EXTEND |
| HBM15DRYH-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USB-I2C-SS | 功能描述:USB 接口集成电路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| USB-ICP-80C51ISP | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC2K | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC9XX | 功能描述:程序设计器 - 基于处理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-SAB9 | 功能描述:插座和适配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
发布紧急采购，3分钟左右您将得到回复。