- 您现在的位置：买卖IC网 > PDF目录17007 > USB-I2C/LIN-CONV-Z (Analog Devices Inc)USB TO I2C/LIN CONV BOARD PDF资料下载
参数资料
| 型号： | USB-I2C/LIN-CONV-Z |
| 厂商： | Analog Devices Inc |
| 文件页数： | 66/104页 |
| 文件大小： | 0K |
| 描述： | USB TO I2C/LIN CONV BOARD |
| 标准包装： | 1 |
| 附件类型： | 适配器板 |
| 适用于相关产品： | ARM7TDMI? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页当前第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 64 of 104
Both switching edges are moved by an equal amount
(PWMDAT1 × tCORE) to preserve the symmetrical output
patterns.
Also shown are the PWMSYNC pulse and Bit 0 of the
PWMSTA register, which indicates whether operation is in the
first or second half cycle of the PWM period.
The resulting on times of the PWM signals over the full PWM
period (two half periods) produced by the timing unit can be
written as follows:
On the high side
t0HH = PWMDAT0 + 2(PWMCH0 PWMDAT1) × tCORE
t0HL = PWMDAT0 2(PWMCH0 PWMDAT1) × tCORE
and the corresponding duty cycles (d)
d0H = t0HH/tS = + (PWMCH0 PWMDAT1)/PWMDAT0
and on the low side
t0LH = PWMDAT0 2(PWMCH0 + PWMDAT1)
× tCORE
t0LL = PWMDAT0 + 2(PWMCH0 + PWMDAT1)
× tCORE
and the corresponding duty cycles (d)
dOL = t0LH/tS = (PWMCH0 + PWMDAT1)/PWMDAT0
The minimum permissible t0H and t0L values are zero,
corresponding to a 0% duty cycle. In a similar fashion, the
maximum value is tS, corresponding to a 100% duty cycle.
Figure 70 shows the output signals from the timing unit for
operation in double update mode. It illustrates a general case
where the switching frequency, dead time, and duty cycle are all
changed in the second half of the PWM period. The same value
for any or all of these quantities can be used in both halves of the
PWM cycle. However, there is no guarantee that symmetrical
PWM signals are produced by the timing unit in double update
mode. Figure 70 also shows that the dead time insertions into
the PWM signals are done in the same way as in single update
mode.
04
95
5-
0
29
–PWMDAT01 ÷ 2
0H
0L
PWMSYNC
PWMSTA (0)
PWMDAT01
+PWMDAT01 ÷ 2
–PWMDAT02 ÷ 2
+PWMDAT02 ÷ 2
PWMCH02
PWMCH01
2 × PWMDAT12
2 × PWMDAT11
PWMDAT22 + 1
PWMDAT21 + 1
00
PWMDAT02
Figure 70. Typical PWM Outputs of the 3-Phase Timing Unit
(Double Update Mode)
In general, the on times of the PWM signals in double update
mode can be defined as follows:
On the high side
t0HH = (PWMDAT01/2 + PWMDAT02/2 + PWMCH01 +
PWMCH02 PWMDAT11 PWMDAT12) × tCORE
t0HL = (PWMDAT01
/2 + PWMDAT02/2 PWMCH01
PWMCH02 + PWMDAT11 + PWMDAT12) × tCORE
where Subscript 1 refers to the value of that register during the
first half cycle, and Subscript 2 refers to the value during the
second half cycle.
The corresponding duty cycles (d) are
d0H = t0HH/tS = (PWMDAT01
/2 + PWMDAT02/2 +
PWMCH01 + PWMCH02 PWMDAT11 PWMDAT12)/
(PWMDAT01 + PWMDAT02)
On the low side
t0LH = (PWMDAT01/2 + PWMDAT02/2 + PWMCH01 +
PWMCH02 + PWMDAT11 + PWMDAT12) × tCORE
t0LL = (PWMDAT01
/2 + PWMDAT02/2 PWMCH01
PWMCH02 PWMDAT11 PWMDAT12) × tCORE
where Subscript 1 refers to the value of that register during the
first half cycle, and Subscript 2 refers to the value during the
second half cycle.
The corresponding duty cycles (d) are
d0L = t0LH/tS = (PWMDAT01/2 + PWMDAT02/2 +
PWMCH01 + PWMCH02 + PWMDAT11 +
PWMDAT12)/(PWMDAT01 + PWMDAT02)
For the completely general case in double update mode
(see Figure 70), the switching period is given by
tS = (PWMDAT01 + PWMDAT02) × tCORE
Again, the values of t0H and t0L are constrained to lie between
zero and tS.
PWM signals similar to those illustrated in Figure 69 and
Figure 70 can be produced on the 1H, 1L, 2H, and 2L outputs by
programming the PWMCH1 and PWMCH2 registers in a manner
identical to that described for PWMCH0. The PWM controller
does not produce any PWM outputs until all of the PWMDAT0,
PWMCH0, PWMCH1, and PWMCH2 registers have been written
to at least once. When these registers are written, internal
counting of the timers in the 3-phase timing unit is enabled.
Writing to the PWMDAT0 register starts the internal timing of
the main PWM timer. Provided that the PWMDAT0 register is
written to prior to the PWMCH0, PWMCH1, and PWMCH2
registers in the initialization, the first PWMSYNC pulse and
interrupt (if enabled) appear 1.5 × tCORE × PWMDAT0 seconds
after the initial write to the PWMDAT0 register in single update
mode. In double update mode, the first PWMSYNC pulse
appears after PWMDAT0 × tCORE seconds.
相关PDF资料 |
PDF描述 |
|---|---|
| HBM10DSEI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| EBC35DCSD-S288 | CONN EDGECARD 70POS .100 EXTEND |
| HBM15DRYN-S13 | CONN EDGECARD 30POS .156 EXTEND |
| RBC17DRES-S13 | CONN EDGECARD 34POS .100 EXTEND |
| HBM15DRYH-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USB-I2C-SS | 功能描述:USB 接口集成电路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| USB-ICP-80C51ISP | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC2K | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC9XX | 功能描述:程序设计器 - 基于处理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-SAB9 | 功能描述:插座和适配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
发布紧急采购，3分钟左右您将得到回复。