- 您现在的位置：买卖IC网 > PDF目录17007 > USB-I2C/LIN-CONV-Z (Analog Devices Inc)USB TO I2C/LIN CONV BOARD PDF资料下载
参数资料
| 型号： | USB-I2C/LIN-CONV-Z |
| 厂商： | Analog Devices Inc |
| 文件页数： | 58/104页 |
| 文件大小： | 0K |
| 描述： | USB TO I2C/LIN CONV BOARD |
| 标准包装： | 1 |
| 附件类型： | 适配器板 |
| 适用于相关产品： | ARM7TDMI? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
Data Sheet
ADuC7019/20/21/22/24/25/26/27/28/29
Rev. F | Page 57 of 104
Linearity degradation near ground and AVDD is caused by satu-
ration of the output amplifier, and a general representation of its
effects (neglecting offset and gain error) is illustrated in Figure 64.
The dotted line in Figure 64 indicates the ideal transfer function,
and the solid line represents what the transfer function may
look like with endpoint nonlinearities due to saturation of the
output amplifier. Note that Figure 64 represents a transfer function
in 0-to-AVDD mode only. In 0-to-VREF or 0-to-DACREF mode
(with VREF < AVDD or DACREF < AVDD), the lower nonlinearity is
similar. However, the upper portion of the transfer function
follows the ideal line right to the end (VREF in this case, not AVDD),
showing no signs of endpoint linearity errors.
0
495
5-
02
4
AVDD
AVDD – 100mV
100mV
0x00000000
0x0FFF0000
Figure 64. Endpoint Nonlinearities Due to Amplifier Saturation
The endpoint nonlinearities conceptually illustrated in
Figure 64 get worse as a function of output loading. Most
of the ADuC7019/20/21/22/24/25/26/27/28/29 data sheet
specifications assume a 5 kΩ resistive load to ground at the
DAC output. As the output is forced to source or sink more
current, the nonlinear regions at the top or bottom (respectively)
of Figure 64 become larger. With larger current demands, this
can significantly limit output voltage swing.
POWER SUPPLY MONITOR
The power supply monitor regulates the IOVDD supply on the
ADuC7019/20/21/22/24/25/26/27/28/29. It indicates when the
IOVDD supply pin drops below one of two supply trip points.
The monitor function is controlled via the PSMCON register.
If enabled in the IRQEN or FIQEN register, the monitor
interrupts the core using the PSMI bit in the PSMCON MMR.
This bit is immediately cleared after CMP goes high.
This monitor function allows the user to save working registers
to avoid possible data loss due to low supply or brown-out
conditions. It also ensures that normal code execution does
not resume until a safe supply level is established.
Table 53. PSMCON Register
Name
Address
Default Value
Access
PSMCON
0xFFFF0440
0x0008
R/W
Table 54. PSMCON MMR Bit Descriptions
Bit
Name
Description
3
CMP
Comparator bit. This is a read-only bit that
directly reflects the state of the comparator.
Read 1 indicates that the IOVDD supply is above
its selected trip point or that the PSM is in
power-down mode. Read 0 indicates that the
IOVDD supply is below its selected trip point. This
bit should be set before leaving the interrupt
service routine.
2
TP
Trip point selection bit. 0 = 2.79 V, 1 = 3.07 V.
1
PSMEN
Power supply monitor enable bit. Set to 1 to
enable the power supply monitor circuit. Cleared
to 0 to disable the power supply monitor circuit.
0
PSMI
Power supply monitor interrupt bit. This bit is set
high by the MicroConverter after CMP goes low,
indicating low I/O supply. The PSMI bit can be
used to interrupt the processor. After CMP
returns high, the PSMI bit can be cleared by
writing a 1 to this location. A 0 write has no
effect. There is no timeout delay; PSMI can be
immediately cleared after CMP goes high.
COMPARATOR
The ADuC7019/20/21/22/24/25/26/27/28/29 integrate voltage
comparators. The positive input is multiplexed with ADC2, and
the negative input has two options: ADC3 and DAC0. The output
of the comparator can be configured to generate a system inter-
rupt, be routed directly to the programmable logic array, start
an ADC conversion, or be on an external pin, CMPOUT, as
shown in Figure 65.
04
95
5-
02
5
MUX
IRQ
MUX
DAC0
ADC2/CMP0
ADC3/CMP1
P0.0/CMPOUT
Figure 65. Comparator
Note that because the ADuC7022, ADuC7025, and ADu7027
parts do not support a DAC0 output, it is not possible to use
DAC0 as a comparator input on these parts.
Hysteresis
Figure 66 shows how the input offset voltage and hysteresis
terms are defined.
04
95
5-
0
63
CMPOUT
CMP0
VH
VOS
Figure 66. Comparator Hysteresis Transfer Function
相关PDF资料 |
PDF描述 |
|---|---|
| HBM10DSEI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| EBC35DCSD-S288 | CONN EDGECARD 70POS .100 EXTEND |
| HBM15DRYN-S13 | CONN EDGECARD 30POS .156 EXTEND |
| RBC17DRES-S13 | CONN EDGECARD 34POS .100 EXTEND |
| HBM15DRYH-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USB-I2C-SS | 功能描述:USB 接口集成电路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| USB-ICP-80C51ISP | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC2K | 功能描述:程序设计器 - 基于处理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-LPC9XX | 功能描述:程序设计器 - 基于处理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| USB-ICP-SAB9 | 功能描述:插座和适配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
发布紧急采购，3分钟左右您将得到回复。