参数资料
型号: XRT83L34IV-F
厂商: Exar Corporation
文件页数: 11/99页
文件大小: 0K
描述: IC LIU T1/E1/J1 QUAD 128TQFP
标准包装: 72
类型: 线路接口装置(LIU)
驱动器/接收器数: 4/4
规程: T1,E1,J1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 128-LQFP
供应商设备封装: 128-TQFP(14x20)
包装: 托盘
其它名称: XRT83L34IV-F-ND
xr
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR REV. 1.0.1
16
RDY_DTACK
RXMUTE
73
O
I
Ready or DTACK Output/Receive Muting upon LOS Command Input
pin:
The exact function of this input pin depends upon whether the XRT83L34
device has been configured to operate in the HOST or Hardware Mode, as
described below.
HOST Mode Operation - READY or DTACK Output Pin:
The exact function of this input pin depends upon which mode the Micropro-
cessor Interface has been configured to operate in, as described below.
Intel-Asynchronous Mode - RDY* - Ready Output:
If the Microprocessor Interface has been configured to operate in the Intel-
Asynchronous Mode, then this output pin will function as the "active-low"
READY output.
During a READ or WRITE cycle, the Microprocessor Interface block will tog-
gle this output pin to the logic low level, ONLY when it (the Microprocessor
Interface) is ready to complete or terminate the current READ or WRITE
cycle. Once the Microprocessor has determined that this input pin has tog-
gled to the logic "low" level, then it is now safe for it to move on and execute
the next READ or WRITE cycle.
If (during a READ or WRITE cycle) the Microprocessor Interface block is
holding this output pin at a logic "high" level, then the Microprocessor is
expected to extend this READ or WRITE cycle, until it detects this output pin
being toggled to the logic low level.
Motorola-Asynchronous Mode - DTACK* - Data Transfer Acknowledge
Output:
If the Microprocessor interface has been configured to operate in the Motor-
ola-Asynchronous Mode, then this output pin will function as the "active-low"
DTACK output.
During a READ or WRITE cycle, the Microprocessor Interface block will tog-
gle this output pin to the logic low level, ONLY when it (the Microprocessor
Interface) is ready to complete or terminate the current READ or WRITE
cycle. Once the Microprocessor Interface has determined that this input pin
has toggled to the logic "low" level, then it is now safe for it to move on and
execute the next READ or WRITE cycle.
If (during a READ or WRITE cycle) the Microprocessor Interface block is
holding this output pin at a logic "HIGH" level, then the MIcroprocessor is
expected to extend this READ or WRITE cycle, until it detects this output pin
being toggled to the logic "LOW" level.
Receive Muting - Hardware mode
NOTE: Internally pulled “Low” with a 50k
resistor.
SIGNAL NAME
PIN #TYPE
DESCRIPTION
相关PDF资料
PDF描述
XRT83L38IB-F IC LIU T1/E1/J1 OCTAL 225BGA
XRT83SH314IB-F IC LIU T1/E1/J1 14CH 304TBGA
XRT83SH38IB-F IC LIU SH T1/E1/J1 8CH 225BGA
XRT86L30IV-F IC LIU/FRAMER TI/E1/J1 SGL 128LQ
XRT86VL30IV-F IC FRAMR/LIU T1/E1/J1 QD 128LQFP
相关代理商/技术参数
参数描述
XRT83L34IVTR 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT83L34IVTR-F 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT83L38 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L38_07 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L38ES 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray