参数资料
| 型号： | XRT83L34IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 82/99页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1/J1 QUAD 128TQFP |
| 标准包装： | 72 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 4/4 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-LQFP |
| 供应商设备封装： | 128-TQFP（14x20） |
| 包装： | 托盘 |
| 其它名称： | XRT83L34IV-F-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页当前第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页
xr
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR REV. 1.0.1
80
CLOCK SELECT REGISTER
The input clock source is used to generate all the necessary clock references internally to the LIU. The
microprocessor timing is derived from a PLL output which is chosen by programming the Clock Select Bits and
the Master Clock Rate in register 0x41h. Therefore, if the clock selection bits or the MCLRATE bit are being
programmed, the frequency of the PLL output will be adjusted accordingly. During this adjustment, it is
important to "Not" write to any other bit location within the same register while selecting the input/output clock
frequency. For best results, whenever the user is changing bits D[6:3] (within the Clock Select Register), he/
she should execute a "Masked-Write" Operation, such that he/she will not change the remaining bits within this
register (e.g., D[7] and D[2:0] as shown below in Figure 29).
FIGURE 29. REGISTER 0X81H SUB REGISTERS
Programming Examples:
Example 1: Changing bits D[6:3]
If bits D[6:3] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 2: Changing bits D[7] and D[2:0]
If bits D[7] and D[2:0] are the only values within the register that will change in a WRITE process, the
microprocessor only needs to initiate ONE write operation.
Example 3: Changing bits within D[6:3] and the other bits
In this scenario, one must initiate TWO write operations such that bits D[6:3] and the other bits do not change
within ONE write cycle. It is recommended that bits D[6:0] and the other bits be treated as two independent
sub-registers. One can either change the clock selection bits and then change bits D[7] and D[2:0] on the
SECOND write, or vice-versa. No order or sequence is necessary.
D0
D1
D2
D3
D4
D5
D6
D7
Clock Selection Bits
ExLOS, ICT
E1arben
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83L38IB-F | IC LIU T1/E1/J1 OCTAL 225BGA |
| XRT83SH314IB-F | IC LIU T1/E1/J1 14CH 304TBGA |
| XRT83SH38IB-F | IC LIU SH T1/E1/J1 8CH 225BGA |
| XRT86L30IV-F | IC LIU/FRAMER TI/E1/J1 SGL 128LQ |
| XRT86VL30IV-F | IC FRAMR/LIU T1/E1/J1 QD 128LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83L34IVTR | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83L34IVTR-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83L38 | 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38_07 | 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38ES | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。