参数资料
| 型号： | XRT83L34IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 22/99页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1/J1 QUAD 128TQFP |
| 标准包装： | 72 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 4/4 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-LQFP |
| 供应商设备封装： | 128-TQFP（14x20） |
| 包装： | 托盘 |
| 其它名称： | XRT83L34IV-F-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页
xr
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR REV. 1.0.1
26
FUNCTIONAL DESCRIPTION
The XRT83L34 is a fully integrated four-channel long-haul and short-haul transceiver intended for T1, J1 or E1
systems. Simplified block diagrams of the device are shown in Figure 1, Host mode and Figure 2, Hardware
mode. The XRT83L34 can receive signals that have been attenuated from 0 to 36dB at 772kHz (0 to 6000 feet
cable loss) for T1 and from 0 to 43dB at 1024kHz for E1 systems.
In T1 applications, the XRT83L34 can generate five transmit pulse shapes to meet the short-haul Digital Cross-
connect (DSX-1) template requirement as well as four CSU Line Build-Out (LBO) filters of 0dB, -7.5dB, -15dB
and -22.5dB as required by FCC rules. It also provides programmable transmit output pulse generators for
each channel that can be used for output pulse shaping allowing performance improvement over a wide variety
of conditions. The operation and configuration of the XRT83L34 can be controlled through a parallel
microprocessor Host interface or, by Hardware control.
MASTER CLOCK GENERATOR
Using a variety of external clock sources, the on-chip frequency synthesizer generates the T1 (1.544MHz) or
E1 (2.048MHz) master clocks necessary for the transmit pulse shaping and receive clock recovery circuit.
There are two master clock inputs MCLKE1 and MCLKT1. In systems where both T1 and E1 master clocks are
available these clocks can be connected to the respective pins. All channels of a given XRT83L34 must be
operated at the same clock rate, either T1, E1 or J1 modes.
In systems that have only one master clock source available (E1 or T1), that clock should be connected to both
MCLKE1 and MCLKT1 inputs for proper operation. T1 or E1 master clocks can be generated from 8kHz,
16kHz, 56kHz, 64kHz, 128kHz and 256kHz external clocks under the control of CLKSEL[2:0] inputs according
to Table 1.
FIGURE 4. TWO INPUT CLOCK SOURCE
FIGURE 5. ONE INPUT CLOCK SOURCE
MCLKE1
MCLKT1
MCLKOUT
1.544MHz
or
2.048MHz
+/-50ppm
1.544MHz
+/-50ppm
Two Input Clock Sources
MCLKE1
MCLKT1
MCLKOUT
1.544MHz
or
2.048MHz
One Input Clock Source
Input Clock Options
8kHz
16kHz
56kHz
64kHz
128kHz
256kHz
1.544MHz
2.048MHz
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83L38IB-F | IC LIU T1/E1/J1 OCTAL 225BGA |
| XRT83SH314IB-F | IC LIU T1/E1/J1 14CH 304TBGA |
| XRT83SH38IB-F | IC LIU SH T1/E1/J1 8CH 225BGA |
| XRT86L30IV-F | IC LIU/FRAMER TI/E1/J1 SGL 128LQ |
| XRT86VL30IV-F | IC FRAMR/LIU T1/E1/J1 QD 128LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83L34IVTR | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83L34IVTR-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83L38 | 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38_07 | 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83L38ES | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。