- 您现在的位置：买卖IC网 > PDF目录1894 > AD9887AKSZ-140 (Analog Devices Inc)IC INTRFACE ANALOG/DVI 160-MQFP PDF资料下载
参数资料
| 型号： | AD9887AKSZ-140 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/52页 |
| 文件大小： | 0K |
| 描述： | IC INTRFACE ANALOG/DVI 160-MQFP |
| 标准包装： | 24 |
| 应用： | 图形卡，VGA 接口 |
| 接口： | 模拟和数字 |
| 电源电压： | 3.15 V ~ 3.45 V |
| 封装/外壳： | 160-BQFP |
| 供应商设备封装： | 160-MQFP（28x28） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 788 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
AD9887A
Rev. B | Page 17 of 52
THEORY OF OPERATION AND DESIGN GUIDE—ANALOG INTERFACE
GENERAL DESCRIPTION
The AD9887A is a fully integrated solution for capturing analog
RGB signals and digitizing them for display on flat panel monitors
or projectors. The device is ideal for implementing a computer
interface in HDTV monitors or for serving as the front end to
high performance video scan converters.
Implemented in a high performance CMOS process, the interface
can capture signals with pixel rates of up to 170 MHz, or of up
to 340 MHz with an alternate pixel sampling mode.
The AD9887A includes all necessary input buffering, signal dc
restoration (clamping), offset and gain (brightness and contrast)
adjustment, pixel clock generation, sampling phase control, and
output data formatting. All controls are programmable via a 2-wire
serial interface. Full integration of these sensitive analog functions
makes system design straightforward and less sensitive to the
physical and electrical environment.
With an operating temperature range of 0°C to 70°C, the device
requires no special environmental considerations.
INPUT SIGNAL HANDLING
The AD9887A has three high impedance analog input pins for
the red, green, and blue channels that accommodate signals
ranging from 0.5 V to 1.0 V p-p.
Signals are typically brought onto the interface board via a DVI-I
connector, a 15-lead D connector, or BNC connectors. The
AD9887A should be located as close as is practical to the input
connector. Signals should be routed via matched-impedance
traces (normally 75 Ω) to the IC input pins.
At this point, the signal should be resistively terminated (75 Ω
to the signal ground return) and capacitively coupled to the
AD9887A inputs through 47 nF capacitors. These capacitors
form part of the dc-restoration circuit (see Figure 3).
In an ideal world of perfectly matched impedances, the best
performance would be obtained with the widest possible signal
bandwidth. The wide bandwidth inputs of the AD9887A
(330 MHz) would track the input signal continuously as it moves
from one pixel level to the next and would digitize the pixel during
a long, flat pixel time. In many systems, however, there are
mismatches, reflections, and noise that result in excessive ringing
and distortion of the input waveform. This makes it difficult to
establish a sampling phase that provides good image quality.
A small inductor in series with the input can be effective in rolling
off the input bandwidth slightly and providing a high quality signal
over a wider range of conditions. Using a Fair-Rite #2508051217Z0
high speed signal chip bead inductor in the circuit of Figure 3
provides good results in most applications.
02838-003
RGB
INPUT
RAIN
GAIN
BAIN
47nF
75
Ω
Figure 3. Analog Input Interface Circuit
HSYNC AND VSYNC INPUTS
The AD9887A receives a horizontal sync signal and uses it to
generate the pixel clock and clamp timing. It is possible to
operate the AD9887A without applying Hsync (using an
external clock), but several of the chip’s features are unavailable.
Therefore, it is recommended to provide Hsync. It can be in the
form of either a sync signal directly from the graphics source or
a preprocessed TTL- or CMOS-level signal.
The HSYNC input includes a Schmitt-trigger buffer and is capable
of handling signals that have long rise times with superior noise
immunity. In typical PC-based graphics systems, the sync signals
are simply TTL-level drivers feeding unshielded wires in the
monitor cable. As such, no termination is required or desired.
When the VSYNC input is selected as the source for Vsync, it is
used for coast generation and passed through to the VSOUT pin.
Serial Control Port
The serial control ports are designed for 3.3 V logic. If there are
5 V drivers on the bus, the serial control port pins should be
protected with 150 Ω series resistors placed between the pull-up
resistors and the input pins.
Output Signal Handling
The digital outputs are designed and specified to operate from a
3.3 V power supply (VDD), but can operate with a VDD as low as
2.5 V for compatibility with 2.5 V logic.
CLAMPING
RGB Clamping
To digitize the incoming signal properly, adjust the dc offset of
the input to fit the range of the on-board ADCs.
Most graphics systems produce RGB signals with black at
ground and white at approximately 0.75 V. However, if sync
signals are embedded in the graphics, the sync tip is often at
ground, the black level is at 300 mV, and the white level is at
approximately 1.0 V. Some common RGB line amplifier boxes
use emitter-follower buffers to split signals and increase drive
capability. This introduces a 700 mV dc offset to the signal.
Clamping removes this offset to allow proper capture.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9888KSZ-170 | IC ANALOG INTRFC 170MSPS 128MQFP |
| AD9895KBCZRL | IC CCD SIGNAL PROC/GEN 64-CSPBGA |
| AD9910BSVZ-REEL | IC DDS 1GSPS 14BIT PAR 100TQFP |
| AD9911BCPZ-REEL7 | IC DDS 500MSPS DAC 10BIT 56LFCSP |
| AD9912ABCPZ | IC DDS 1GSPS DAC 14BIT 64LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9887AKSZ-1401 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Interface for Flat Panel Display |
| AD9887AKSZ-170 | 功能描述:IC INTRFACE ANALOG/DVI 160-MQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| AD9887AKSZ-170 | 制造商:Analog Devices 功能描述:IC DUAL DISPLAY INTERFACE |
| AD9887AKSZ-1701 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Interface for Flat Panel Display |
| AD9887APCB | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Interface for Flat Panel Displays |
发布紧急采购，3分钟左右您将得到回复。