- 您现在的位置：买卖IC网 > PDF目录362733 > Enhanced Am486 dx2 (Advanced Micro Devices, Inc.) High-Performance Design On-Chip Integration Complete 32-Bit Architecture Micrprocessor(高性能单片32位微处理器) PDF资料下载
参数资料
| 型号： | Enhanced Am486 dx2 |
| 厂商： | Advanced Micro Devices, Inc. |
| 英文描述： | High-Performance Design On-Chip Integration Complete 32-Bit Architecture Micrprocessor(高性能单片32位微处理器) |
| 中文描述： | 高性能设计的片上集成完整的32位架构Micrprocessor（高性能单片32位微处理器） |
| 文件页数： | 14/69页 |
| 文件大小： | 1068K |
| 代理商： | ENHANCED AM486 DX2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页
Enhanced Am486 Microprocessor
AMD
14
PRELIMINARY
BS8/BS16
Bus Size 8 (Active Low; Input)/
Bus Size 16 (Active Low; Input)
The BS8 and BS16 signals allow the processor to op-
erate with 8-bit and 16-bit I/O devices by running multi-
ple bus cycles to respond to data requests: four for 8-
bit devices, and two for 16-bit devices. The bus sizing
pins are sampled every clock. The microprocessor sam-
ples the pins every clock before RDY to determine the
appropriate bus size for the requesting device. The sig-
nals are active Low input with internal pull-up resistors,
and must satisfy setup and hold times t
14
and t
15
for
correct operation. Bus sizing is not permitted during
copy-back or write-back operation. BS8 and BS16 are
ignored during copy-back or write-back cycles.
CACHE – New
Internal Cacheability (Active Low; Output)
In write-through mode, this signal always floats. In write-
back mode for processor-initiated cycles, a Low output
on this pin indicates that the current read cycle is cache-
able, or that the current cycle is a burst write-back or
copy-back cycle. If the CACHE signal is driven High
during a read, the processor will not cache the data even
if the KEN pin signal is asserted. If the processor deter-
mines that the data is cacheable, CACHE goes active
when ADS is asserted and remains in that state until the
next RDY or BRDY is asserted. CACHE floats in re-
sponse to a BOFF or HOLD request.
CLK – Modified
Clock (Input)
The CLK input provides the basic microprocessor timing
signal. The CLKMUL input selects the multiplier value
used to generate the internal operating frequency for
the Enhanced Am486 microprocessor family. All exter-
nal timing parameters are specified with respect to the
rising edge of CLK. The clock signal passes through an
internal Phase-Lock Loop (PLL).
CLKMUL
–
New
Clock Multiplier (Input)
The microprocessor samples the CLKMUL input signal
at RESET to determine the design operating frequency.
An internal pull-up resistor connects to V
CC
, which se-
lects clock-tripled mode if the input is High or left floating.
For clock-doubled mode, the input must be pulled Low.
For DX2 versions, this input must always be connected
to V
SS
to ensure correct operation.
D31
–
D0
Data Lines (Inputs/Outputs)
Lines D31–D0 define the data bus. The signals must
meet setup and hold times t
22
and t
23
for proper read op-
erations. These pins are driven during the second and sub-
sequent clocks of write cycles.
D/C
Data/Control (Output)
This bus cycle definition pin distinguishes memory and
I/O data cycles from control cycles. The control cycles
are:
n
Interrupt Acknowledge
n
Halt/Special Cycle
n
Code Read (instruction fetching)
DP3
–
DP0
Data Parity (Inputs/Outputs)
Data parity is generated on all write data cycles with the
same timing as the data driven by the microprocessor.
Even parity information must be driven back into the
microprocessor on the data parity pins with the same
timing as read information to ensure that the processor
uses the correct parity check. The signals read on these
pins do not affect program execution. Input signals must
meet setup and hold times t
22
and t
23
. DP3–DP0 should
be connected to V
CC
through a pull-up resistor in systems
not using parity. DP3–DP0 are active High and are driven
during the second and subsequent clocks of write cycles.
EADS – Modified
External Address Strobe (Active Low; Input)
This signal indicates that a valid external address has
been driven on the address pins A31–A4 of the micro-
processor to be used for a cache snoop. This signal is
recognized while the processor is in hold (HLDA is driv-
en active), while forced off the bus with the BOFF input,
or while AHOLD is asserted. The microprocessor ig-
nores EADS at all other times. EADS is not recognized
if HITM is active, nor during the clock after ADS, nor
during the clock after a valid assertion of EADS. Snoops
to the on-chip cache must be completed before another
snoop cycle is initiated. Table 2 describes EADS when
first sampled. EADS can be asserted every other clock
cycle as long as the hold remains active and HITM re-
mains inactive. INV is sampled in the same clock period
that EADS is asserted. EADS has an internal weak pull-up.
Note:
The triggering signal (AHOLD, HOLD, or BOFF)
must remain active for at least 1 clock after EADS to
ensure proper operation.
Table 2. EADS Sample Time
Trigger
EADS First Sampled
AHOLD
HOLD
BOFF
Second clock after AHOLD asserted
First clock after HLDA asserted
Second clock after BOFF asserted
相关PDF资料 |
PDF描述 |
|---|---|
| Enhanced Am486 dx4 | High-Performance Design On-Chip Integration Complete 32-Bit Architecture Micrprocessor(高性能设计片上集成完全32位体系微处理器) |
| EO12 | IRDA INFRARED TRANSCEIVER |
| EOL-62L256 | HT62L256 EOL Notification |
| EP05FA20 | FRD |
| EP05Q03L | SBD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ENHSAURR8 | 制造商:Molex 功能描述:8 PORT MACHINE MOUNT SWITCH 制造商:Molex 功能描述:COMPUTERS, NETWORK SWITCHES CONNECTIVITY, No. of Ports:8, Data Rate Max:100Mbps, |
| ENHSDURR5 | 制造商:Molex 功能描述:COMPUTERS, NETWORK SWITCHES CONNECTIVITY, No. of Ports:5, Switch Mounting:DIN Ra 制造商:Molex 功能描述:ETHERNET DIN RAIL SWITCH 5PORT |
| ENHSDURR9 | 制造商:MOLEX/WOODHEAD 功能描述:Ethernet Network Switch 制造商:Molex 功能描述:ETHERNET NETWORK SWITCH, No. of Ports:9, Data Rate Max:100Mbps, Switch Mounting: |
| ENI-110 | 功能描述:冲压机与冲模 NON-IMPACT PUNCHDOWN TOOL RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| ENICSF2811PBKA | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。