- 您现在的位置：买卖IC网 > PDF目录69323 > RTPXA270C0C312 (INTEL CORP) 312 MHz, RISC PROCESSOR, PBGA356 PDF资料下载
参数资料
| 型号： | RTPXA270C0C312 |
| 厂商： | INTEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 312 MHz, RISC PROCESSOR, PBGA356 |
| 封装： | 13 X 13 MM, 1 MM HEIGHT, 0.50 MM PITCH, LEAD FREE, VFBGA-356 |
| 文件页数： | 71/128页 |
| 文件大小： | 1560K |
| 代理商： | RTPXA270C0C312 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页当前第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
Electrical, Mechanical, and Thermal Specification
4-27
Intel PXA270 Processor
Pin Listing and Signal Definitions
4.3
Signal Types
Table 4-2. Pin Usage and Mapping Notes
Note
Description
[1]
GPIO reset/deep sleep operation: After any reset is asserted or if the PXA270 processor is in deep sleep mode, these
pins are configured as GPIO inputs by default. The input buffers for these pins are disabled to prevent current drain and
must be enabled prior to use by clearing the read disable hold bit, PSSR[RDH]. Until RDH is cleared, each pin is pulled
high (Pu-1), pulled low (Pd-0), or floated (Hi-Z).
[2]
Crystal oscillator pins: These pins connect the external crystals to the on-chip oscillators and are not affected by either
reset or sleep. For more information, see the “Clocks and Power” chapter in the Intel PXA27x Processor Family
Developer’s Manual.
[3]
GPIO sleep operation: During the transition into sleep mode, the configuration of these pins is determined by the
corresponding GPIO setting. This pin is not driven during sleep if the direction of the pin is selected to be an input. If the
direction of the pin is selected as an output, the value contained in the Power Manager GPIO Sleep-State register
(PGSR0/1/2/3) is driven out onto the pin and held while the PXA270 processor is in sleep mode.
Upon exit from sleep mode, GPIOs that are configured as outputs continue to hold the standby, sleep, or deep-sleep state
until software clears the peripheral control hold bit, PSSR[PH]. Software must clear this bit (by writing 0b1 to it) after the
peripherals have been fully configured, as described in Note[1], but before the process actually uses them.
GPIOs that are configured as inputs immediately after exiting sleep mode cannot be used until PSSR[RDH] is cleared.
[4]
Static memory control pins: During sleep mode, these pins can be programmed either to drive the value in the Power
Manager GPIO Sleep-State register (PGSR0/1/2/3) or to be placed in a Hi-Z (undriven) state. To select the Hi-Z state,
software must set PCFR[FS]. If FS is not set, these pins function as described in Note[3] during the transition to sleep
mode.
[5]
PCMCIA control pins: During sleep mode, these pins can be programmed either to drive the value in the Power Manager
GPIO Sleep-State register (PGSR0/1/2/3) or to be placed in a Hi-Z (undriven) state. To select the Hi-Z state, software
must set PCFR[FP]. If FP is not set, these pins function as described in Note[3] during the transition to sleep mode.
[6]
(reserved)
[7]
When the power manager overrides the GPIO alternate function, the Power Manager GPIO Sleep-State registers
(PGSR0/1/2/3) and the PSSR[RDH] bit are ignored. Pullup and pulldown are disabled immediately after the power
manager overrides the GPIO function.
[8]
Output functions during sleep mode
[9]
Pull-up always enabled
[10]
(reserved)
[11]
Pins do not function during sleep mode if the OS timer is active
[12]
Pins must be floated by software during sleep mode (floating does not happen automatically)
[13]
(reserved)
[14]
(reserved)
[15]
The pin is three-stateable (Hi-Z) based on the value of PCFR[FS]. There is no PGSR0/1/2/3 setting associated with the
pin because it is not a GPIO.
[16]
PWR_EN goes high during reset, between the assertion of the reset pin and the de-assertion of internal reset within the
PXA270 processor, after SYS_EN is driven high.
[17]
GPIOs 114 and115: The alternate function configuration of these pins is ignored when either PUCR[USIM114] or
PUCR[USIM115] bits are set. Setting these bits forces the USIM enable signal onto these GPIOs.
[18]
When software sets the OSCC[PIO_EN] or OSCC[TOUT_EN] bits, then any GPIO alternate function setting applied to
GPIO<9> or GPIO <10> is overridden with the CLK_PIO function on GPIO<9> and CLK_TOUT on GPIO<10>.
[19]
Refer to Table 4-4.
相关PDF资料 |
PDF描述 |
|---|---|
| RCPXA270C0C520 | 520 MHz, MICROPROCESSOR, PBGA356 |
| RV5C387A-F | 0 TIMER(S), REAL TIME CLOCK, PDSO10 |
| RX-4571LC | REAL TIME CLOCK, PDSO12 |
| RX-4571SA | REAL TIME CLOCK, PDSO14 |
| RX-4571SA | 0 TIMER(S), REAL TIME CLOCK, PDSO14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RTPXA270C0C416 | 制造商:Intel 功能描述:MPU PXA270 416MHz 3V/3.3V 356-Pin VFBGA |
| RTPXA270C0C624 | 制造商:Intel 功能描述:MPU PXA270 624MHz 3V/3.3V 356-Pin VFBGA |
| RTPXA270C5C208 S L977 | 制造商:Marvell 功能描述:Marvell RTPXA270C5C208 S L977 Microprocessors |
| RTPXA270C5C312 | 功能描述:IC MPU 32BIT 312MHZ 356-PBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:- 标准包装:1 系列:MPC85xx 处理器类型:32-位 MPC85xx PowerQUICC III 特点:- 速度:1.2GHz 电压:1.1V 安装类型:表面贴装 封装/外壳:783-BBGA，FCBGA 供应商设备封装:783-FCPBGA（29x29） 包装:托盘 |
| RTPXA270C5C312 868403 | 制造商:Marvell 功能描述: |
发布紧急采购，3分钟左右您将得到回复。