收藏本站
参数资料
型号： ST7285C
厂商： 意法半导体
英文描述： 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES
中文描述： 8位微控制器48,000铁路发展策略光盘，3K内存，ADC，两个定时器，2个SPI，I2C和脊髓损伤接口
文件页数： 37/117页
文件大小： 748K
代理商： ST7285C
37/117
ST7285C
16-BIT TIMER
(Cont’d)
When the counter rolls over from FFFFh to 0000h,
the Timer Overflow flag (TOF) of the Timer Status
Register (TSR) is set. A timer interrupt is then gen-
erated if the TOIE enable bit of the Timer Control
Register (TCR1) is set, provided the I bit of the
CCR is cleared. If one of these conditions is false,
the interrupt remains pending to be issued as soon
as they are both true. The interrupt request is
cleared by reading TSR while TOF is set, followed
by an access (read or write) to the LSB of the
Counter Register.
The TOF flag is not affected by accesses to the Al-
ternate Counter Register. This feature allows si-
multaneous use of the overflow function and reads
of the free running counter at random times (for
example, to measure elapsed time) without risking
to clear the TOF flag erroneously. Accesses to the
timer without the intention of servicing the TOF
flag should therefore be performed to the Alternate
Counter Register while only the TOF service rou-
tine accesses the Counter Register.
The free running counter can be reset under soft-
ware control, by writing to the LSB of the Counter
Register or of the Alternate Counter Register. The
counter and the prescaler are then configured to
their reset conditions. This reset also completes
any 16-bit access sequence. All flags and enable
bits are unchanged.
The value in the counter registers repeats every
131,072, 262,144, or 524,288 internal processor
clock cycles, depending on the clock control option
selected in TCR2. As shown in the timing dia-
grams, the counter increment is triggered by a fall-
ing edge of the CPU clock.
The timer is not affected by WAIT mode. In HALT
mode, the counter stops counting until the mode is
exited. Counting then resumes from the previous
count (MCU awakened by an interrupt) or from the
reset count (MCU awakened by a Reset).
4.3.3 External Clock
When the external clock is selected by setting the
relevant clock control bits in TCR2, the counter
clocks on each external clock rising edge, if
EXEDG in TCR2 is set, or the falling edges if reset,
and is synchronised with the falling edge of the in-
ternal CPU clock.
At least four falling edges of the CPU clock must
occur between two consecutive active edges of
the external clock; thus the external clock frequen-
cy must be less than a quarter of the CPU clock
frequency.
The parasitic pulses generated by the EXTEDG
and EXTCLKE transitions are filtered during two
clock periods, so the manipulation of the external
clock control bits must occur before or after two in-
ternal clock periods.
相关PDF资料
PDF描述
ST72T85A5Q6 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES
ST730C08L3 PHASE CONTROL THYRISTORS
ST730C08L3L PHASE CONTROL THYRISTORS
ST730C12L0 PHASE CONTROL THYRISTORS
ST730C12L0L PHASE CONTROL THYRISTORS
相关代理商/技术参数
参数描述
ST7-28B56 功能描述:电源变压器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率额定值:12 VA 初级电压额定值:115 V / 230 V 次级电压额定值:12 V / 24 V 安装风格:SMD/SMT 一次绕组:Dual Primary Winding 二次绕组:Dual Secondary Winding 长度:2.5 in 宽度:2 in 高度:1.062 in
ST72A 制造商:DGS 功能描述:
ST72C104G1B6 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72C104G1M1 制造商:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER - Bulk
ST72C104G1M6 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*