参数资料
型号: ST7285C
厂商: 意法半导体
英文描述: 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES
中文描述: 8位微控制器48,000铁路发展策略光盘,3K内存,ADC,两个定时器,2个SPI,I2C和脊髓损伤接口
文件页数: 42/117页
文件大小: 748K
代理商: ST7285C
42/117
ST7285C
16-BIT TIMER
(Cont’d)
4.3.5.2 Forced Compare Mode
The main purpose of the Forced Compare mode is
to facilitate fixed frequency generation.
In this sectioni may represent 1 or 2.
When the Forced Output Level i bit (FOLVi) of
TCR1 is written to 1, OLVLiis copied to theOCMPi
pin. To provide this capability, internal logic allows
a single instruction to change OLVLi and causes a
forced compare with the new value of OLVL. OCFi
is not affected, and thus no interrupt request is
generated.
4.3.5.3 One Pulse Mode
The One Pulse mode enables the generation of a
pulse on the occurence of an external event and is
programmed via the OPM bit in the TCR2 register.
The trigger event is applied to the Input Capture1
pin (ICAP1); the active edge of the event is flagged
by the IEDG1 bit in TCR1.
Then, on an event on ICAP1, the counter is initial-
ized to FFFCh and OLVL2 is loaded on the output
compare 1 pin (OCMP1); when the value of the
counter is equal to the value of the contents of
OCR1, the OLVL1 bit is output on the Output Com-
pare 1 pin (OCMP1). No interrupt is generated.
(See Figure 9).
4.3.5.4 Pulse Width Modulation Mode
This mode is similar to the One Pulse mode, in
which the external event is replaced by the Output
Compare 2 event; this mode is programmed via
the PWM bit in the TCR2 register.
OCR1 then contains the length of the pulse, while
OCR2 contains the value of the period; the Output
Compare 2 event causes the counter to be initial-
ized to FFFCh (See Figure 10). No interrupt is
generated
Figure 25. One Pulse Mode Timing, IEDG1=1; OCR1=2ED0h
Figure 26. Pulse Width Modulation Mode Timing, OCR1=2ED0h, OCR2=34E2
COUNTER
....
FFFC FFFD FFFE
2ED0
2ED1 2ED2
2ED3
FFFC FFFD
OLVL2
OLVL2
OLVL1
ICAP1
OCMP1
compare1
COUNTER
34E2
FFFC FFFD FFFE
2ED0 2ED1 2ED2
34E2
FFFC
OLVL2
OLVL2
OLVL1
OCMP1
compare2
compare1
compare2
相关PDF资料
PDF描述
ST72T85A5Q6 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES
ST730C08L3 PHASE CONTROL THYRISTORS
ST730C08L3L PHASE CONTROL THYRISTORS
ST730C12L0 PHASE CONTROL THYRISTORS
ST730C12L0L PHASE CONTROL THYRISTORS
相关代理商/技术参数
参数描述
ST7-28B56 功能描述:电源变压器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率额定值:12 VA 初级电压额定值:115 V / 230 V 次级电压额定值:12 V / 24 V 安装风格:SMD/SMT 一次绕组:Dual Primary Winding 二次绕组:Dual Secondary Winding 长度:2.5 in 宽度:2 in 高度:1.062 in
ST72A 制造商:DGS 功能描述:
ST72C104G1B6 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72C104G1M1 制造商:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER - Bulk
ST72C104G1M6 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT