- 您现在的位置：买卖IC网 > PDF目录202140 > W949D2CBJX5E (WINBOND ELECTRONICS CORP) 16M X 32 DDR DRAM, 5 ns, PBGA90 PDF资料下载
参数资料
| 型号： | W949D2CBJX5E |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | DRAM |
| 英文描述： | 16M X 32 DDR DRAM, 5 ns, PBGA90 |
| 封装： | 8 X 13 MM, 0.80 MM PITCH, HALOGEN FREE AND LEAD FREE, VFBGA-90 |
| 文件页数： | 2/60页 |
| 文件大小： | 1160K |
| 代理商： | W949D2CBJX5E |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
W949D6CB / W949D2CB
512Mb Mobile LPDDR
Publication Release Date: Jun, 14, 2011
- 10 -
Revision A01-006
6. FUNCTION DESCRIPTION
6.1 Initialization
LPDDR SDRAM must be powered up and initialized in a predefined manner. Operations procedures other than
those specified may result in undefined operation. If there is any interruption to the device power, the initialization
routine should be followed. The steps to be followed for device initialization are listed below.
The Mode Register and Extended Mode Register do not have default values. If they are not programmed during the
initialization sequence, it may lead to unspecified operation. The clock stop feature is not available until the device
has been properly initialized from Step 1 through 11.
Step 1: Provide power, the device core power (VDD) and the device I/O power (VDDQ) must be brought up
simultaneously to prevent device latch-up. Although not required, it is recommended that VDD and
VDDQ are from the same power source. Also Assert and hold Clock Enable (CKE) to a LVCMOS logic
high level
Step 2: Once the system has established consistent device power and CKE is driven high, it is safe to apply
stable clock.
Step 3: There must be at least 200
μs of valid clocks before any command may be given to the DRAM. During this
time NOP or DESELECT commands must be issued on the command bus.
Step 4: Issue a PRECHARGE ALL command.
Step 5: Provide NOPs or DESELECT commands for at least tRP time.
Step 6: Issue an AUTO REFRESH command followed by NOPs or DESELECT command for at least tRFC time.
Issue the second AUTO REFRESH command followed by NOPs or DESELECT command for at least
tRFC time. Note as part of the initialization sequence there must be two Auto Refresh commands issued.
The typical flow is to issue them at Step 6, but they may also be issued between steps 10 and 11.
Step 7: Using the MRS command, program the base mode register. Set the desired operation modes.
Step 8: Provide NOPs or DESELECT commands for at least tMRD time.
Step 9: Using the MRS command, program the extended mode register for the desired operating modes. Note
the order of the base and extended mode register programmed is not important.
Step 10: Provide NOP or DESELECT commands for at least tMRD time.
Step 11: The DRAM has been properly initialized and is ready for any valid command.
相关PDF资料 |
PDF描述 |
|---|---|
| WF128K32N-150HC5 | 512K X 8 FLASH 5V PROM MODULE, 150 ns, HIP66 |
| WPS512K8LB-85GM | 512K X 8 STANDARD SRAM, 85 ns, PDSO32 |
| WPS128K32GV-17PJI | 512K X 8 MULTI DEVICE SRAM MODULE, 17 ns, PQMA68 |
| WF2M32B-150HM5 | 8M X 8 FLASH 5V PROM MODULE, 150 ns, CHIP66 |
| WF2M32B-120G2UC5 | 8M X 8 FLASH 5V PROM MODULE, 120 ns, CQFP68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W949D2CBJX5ETR | 制造商:Winbond Electronics Corp 功能描述:512M MDDR, X32, 200MHZ |
| W949D2CBJX5I | 制造商:Winbond Electronics Corp 功能描述:DRAM Chip Mobile LPDDR SDRAM 512M-Bit 16Mx32 1.8V 90-Pin VFBGA |
| W949D2CBJX5I TR | 制造商:Winbond Electronics Corp 功能描述:512M MDDR, X32, 200MHZ, INDUST |
| W949D2CBJX6E | 制造商:Winbond Electronics Corp 功能描述:DRAM Chip Mobile LPDDR SDRAM 512M-Bit 16Mx32 1.8V 90-Pin VFBGA |
| W949D2CBJX6ETR | 制造商:Winbond Electronics Corp 功能描述:512M MDDR, X32, 166MHZ, 65NM |
发布紧急采购，3分钟左右您将得到回复。