收藏本站
参数资料
型号： XRT75R12DIB-L
厂商： Exar Corporation
文件页数： 128/133页
文件大小： 0K
描述： IC LIU E3/DS3/STS-1 12CH 420TBGA
标准包装： 40
类型： 线路接口装置（LIU）
驱动器/接收器数： 12/12
规程： DS3，E3，STS-1
电源电压： 3.135 V ~ 3.465 V
安装类型： 表面贴装
封装/外壳： 420-LBGA 裸露焊盘
供应商设备封装： 420-TBGA（35x35）
包装： 托盘
XRT75R12D
90
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.3
8.2.1.1
A Brief Description of an STS-1 Frame
In order to be able to describe how a DS3 signal is asynchronously mapped into an STS-1 SPE, it is important
to define and understand all of the following.
The STS-1 frame structure
The STS-1 SPE (Synchronous Payload Envelope)
Telcordia GR-253-CORE's recommendation on mapping DS3 data into an STS-1 SPE
An STS-1 frame is a data-structure that consists of 810 bytes (or 6480 bits). A given STS-1 frame can be
viewed as being a 9 row by 90 byte column array (making up the 810 bytes). The frame-repetition rate (for an
STS-1 frame) is 8000 frames/second. Therefore, the bit-rate for an STS-1 signal is (6480 bits/frame * 8000
frames/sec =) 51.84Mbps.
A simple illustration of this SONET STS-1 frame is presented below in Figure 38.
Figure 38 indicates that the very first byte of a given STS-1 frame (to be transmitted or received) is located in
the extreme upper left hand corner of the 90 column by 9 row array, and that the very last byte of a given STS-
1 frame is located in the extreme lower right-hand corner of the frame structure. Whenever a Network Element
transmits a SONET STS-1 frame, it starts by transmitting all of the data, residing within the top row of the STS-
1 frame structure (beginning with the left-most byte, and then transmitting the very next byte, to the right). After
the Network Equipment has completed its transmission of the top or first row, it will then proceed to transmit the
second row of data (again starting with the left-most byte, first). Once the Network Equipment has transmitted
the last byte of a given STS-1 frame, it will proceed to start transmitting the very next STS-1 frame.
The illustration of the STS-1 frame (in Figure 38) is very simplistic, for multiple reasons. One major reason is
that the STS-1 frame consists of numerous types of bytes. For the sake of discussion within this data sheet,
the STS-1 frame will be described as consisting of the following types (or groups) of bytes.
The Transport Overheads (or TOH) Bytes
The Envelope Capacity Bytes
8.2.1.1.1
The Transport Overhead (TOH) Bytes
The Transport Overhead or TOH bytes occupy the very first three (3) byte columns within each STS-1 frame.
Figure 39 presents another simple illustration of an STS-1 frame structure. However, in this case, both the
TOH and the Envelope Capacity bytes are designated in this Figure.
FIGURE 38. A SIMPLE ILLUSTRATION OF THE SONET STS-1 FRAME
STS-1 Frame (810 Bytes)
90 Bytes
9 Rows
First Byte of the STS-1 Frame
Last Byte of the STS-1 Frame
相关PDF资料
PDF描述
XRT75R12IB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
XRT75VL00DIV IC LIU E3/DS3/STS-1 1CH 52TQFP
XRT75VL00IV-F IC LIU E3/DS3/STS-1 1CH 52TQFP
XRT79L71IB-F IC LIU/FRAMER DS3/E3 1CH 208BGA
XRT81L27IV-F IC LIU EI 7CH 3.3V 128TQFP
相关代理商/技术参数
参数描述
XRT75R12ES 功能描述:时钟合成器/抖动清除器 12CH T3/E3/STS1LIUJA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75R12IB 功能描述:外围驱动器与原件 - PCI 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75R12IB-F 功能描述:外围驱动器与原件 - PCI 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75R12IB-L 功能描述:LIN 收发器 Attenuator RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
XRT75VL00 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*