收藏本站
参数资料
型号： XRT75R12DIB-L
厂商： Exar Corporation
文件页数： 17/133页
文件大小： 0K
描述： IC LIU E3/DS3/STS-1 12CH 420TBGA
标准包装： 40
类型： 线路接口装置（LIU）
驱动器/接收器数： 12/12
规程： DS3，E3，STS-1
电源电压： 3.135 V ~ 3.465 V
安装类型： 表面贴装
封装/外壳： 420-LBGA 裸露焊盘
供应商设备封装： 420-TBGA（35x35）
包装： 托盘
XRT75R12D
109
REV. 1.0.3
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
NOTE: All of these intrinsic jitter measurements are to be performed using a band-pass filter of 10Hz to 400kHz.
Each of the scenarios presented in Table 43, are briefly described below.
8.5.1
DS3 De-Mapping Jitter
DS3 De-Mapping Jitter is the amount of Intrinsic Jitter that will be measured within the "Line" or "Facility-side"
DS3 signal, (after it has been de-mapped from a SONET signal) without the occurrence of "Pointer
Adjustments" within the SONET signal.
Telcordia GR-253-CORE requires that the "DS3 De-Mapping" Jitter be less than 0.4UI-pp, when measured
over all possible combinations of DS3 and STS-1 frequency offsets.
8.5.2
Single Pointer Adjustment
Telcordia GR-253-CORE states that if each pointer adjustment (within a continuous stream of pointer
adjustments) is separated from each other by a period of 30 seconds, or more; then they are sufficiently
isolated to be considered "Single-Pointer Adjustments".
Figure 55 presents an illustration of the "Single Pointer Adjustment" Scenario.
Telcordia GR-253-CORE states that the Intrinsic Jitter that is measured (within the DS3 signal) that is
ultimately de-mapped from a SONET signal that is experiencing "Single-Pointer Adjustment" events, must
NOT exceed the value 0.3UI-pp + Ao.
NOTES:
1.
Ao is the amount of Intrinsic Jitter that was measured during the "De-Mapping" Jitter portion of this test.
2.
Testing must be performed for both Incrementing and Decrementing Pointer Adjustments.
Continuous Pattern
A4
1.0UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Continuous Add
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Continuous Cancel
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
FIGURE 55. ILLUSTRATION OF SINGLE POINTER ADJUSTMENT SCENARIO
TABLE 43: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3
APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
TELCORDIA GR-253-CORE
CATEGORY I INTRINSIC
JITTER REQUIREMENTS
COMMENTS
Initialization
Cool Down
Measurement Period
>30s
Pointer Adjustment Events
相关PDF资料
PDF描述
XRT75R12IB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
XRT75VL00DIV IC LIU E3/DS3/STS-1 1CH 52TQFP
XRT75VL00IV-F IC LIU E3/DS3/STS-1 1CH 52TQFP
XRT79L71IB-F IC LIU/FRAMER DS3/E3 1CH 208BGA
XRT81L27IV-F IC LIU EI 7CH 3.3V 128TQFP
相关代理商/技术参数
参数描述
XRT75R12ES 功能描述:时钟合成器/抖动清除器 12CH T3/E3/STS1LIUJA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75R12IB 功能描述:外围驱动器与原件 - PCI 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75R12IB-F 功能描述:外围驱动器与原件 - PCI 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75R12IB-L 功能描述:LIN 收发器 Attenuator RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
XRT75VL00 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*