- 您现在的位置：买卖IC网 > PDF目录15166 > ZL6105ALAFTK (Intersil)IC REG CTRLR BUCK PWM VM 36-QFN PDF资料下载
参数资料
| 型号： | ZL6105ALAFTK |
| 厂商： | Intersil |
| 文件页数： | 23/35页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 36-QFN |
| 标准包装： | 1,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.4MHz |
| 占空比： | 95% |
| 电源电压： | 3 V ~ 14 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 36-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
ZL6105
If the desired UVLO threshold is not one of the listed choices, the
user can configure a threshold between 2.85V and 16V by
connecting a resistor between the UVLO pin and SGND by
selecting the appropriate resistor from Table 19.
The default response from an overvoltage fault is to immediately
shut down. The device will continuously check for the presence of
the fault condition, and when the fault condition no longer exists
the device will be re-enabled.
TABLE 19. UVLO THRESHOLD RESISTOR SETTINGS
R UVLO UVLO R UVLO
(k Ω ) (V) (k Ω )
UVLO
(V)
For continuous overvoltage protection when operating from an
external clock, the only allowed response is an immediate
shutdown.
17.8
19.6
21.5
23.7
26.1
28.7
31.6
34.8
38.3
42.2
2.85
3.14
3.44
3.79
4.18
4.59
5.06
5.57
6.13
6.75
46.4
51.1
56.2
61.9
68.1
75
82.5
90.9
100
7.42
8.18
8.99
9.9
10.9
12
13.2
14.54
16
Please refer to Application Note AN2033 for details on how to
select specific overvoltage fault response options via I 2 C/SMBus.
Output Pre-Bias Protection
An output pre-bias condition exists when an externally applied
voltage is present on a power supply’s output before the power
supply’s control IC is enabled. Certain applications require that
the converter not be allowed to sink current during start up if a
pre-bias condition exists at the output. The ZL6105 provides
pre-bias protection by sampling the output voltage prior to
initiating an output ramp.
If a pre-bias voltage lower than the target voltage exists after the
pre-configured delay period has expired, the target voltage is set
to match the existing pre-bias voltage and both drivers are
The UVLO voltage can also be set to any value between 2.85V
and 16V via the I 2 C/SMBus interface.
Once an input undervoltage fault condition occurs, the device
can respond in a number of ways as follows:
1. Continue operating without interruption.
2. Continue operating for a given delay period, followed by
shutdown if the fault still exists. The device will remain in
shutdown until instructed to restart.
3. Initiate an immediate shutdown until the fault has been
cleared. The user can select a specific number of retry
attempts.
The default response from a UVLO fault is an immediate
shutdown of the device. The device will continuously check for
the presence of the fault condition. If the fault condition is no
longer present, the ZL6105 will be re-enabled.
Please refer to Application Note AN2033 for details on how to
configure the UVLO threshold or to select specific UVLO fault
response options via the I 2 C/SMBus interface.
Output Overvoltage Protection
The ZL6105 offers an internal output overvoltage protection
circuit that can be used to protect sensitive load circuitry from
being subjected to a voltage higher than its prescribed limits. A
hardware comparator is used to compare the actual output
voltage (seen at the VSEN pin) to a threshold set to 15% higher
than the target output voltage (the default setting). If the VSEN
voltage exceeds this threshold, the PG pin will de-assert and the
device can then respond in a number of ways as follows:
1. Initiate an immediate shutdown until the fault has been
cleared. The user can select a specific number of retry
attempts.
2. Turn off the high-side MOSFET and turn on the low-side
MOSFET. The low-side MOSFET remains ON until the device
attempts a restart.
23
enabled. The output voltage is then ramped to the final
regulation value at the ramp rate set by the SS pin.
The actual time the output will take to ramp from the pre-bias
voltage to the target voltage will vary depending on the pre-bias
voltage but the total time elapsed from when the delay period
expires and when the output reaches its target value will match
the pre-configured ramp time. See Figure 14.
If a pre-bias voltage higher than the target voltage exists after the
pre-configured delay period has expired, the target voltage is set
to match the existing pre-bias voltage and both drivers are
enabled with a PWM duty cycle that would ideally create the pre-
bias voltage.
Once the pre-configured soft-start ramp period has expired, the
PG pin will be asserted (assuming the pre-bias voltage is not
higher than the overvoltage limit). The PWM will then adjust its
duty cycle to match the original target voltage and the output will
ramp down to the pre-configured output voltage.
If a pre-bias voltage higher than the overvoltage limit exists, the
device will not initiate a turn-on sequence and will declare an
overvoltage fault condition to exist. In this case, the device will
respond based on the output overvoltage fault response method
FN6906.5
December 19, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| RBM18DREI | CONN EDGECARD 36POS .156 EYELET |
| B43086F2476M | 47UF 250V 16X20 SINGLE END |
| ISL6307CRZ-T | IC REG CTRLR BUCK PWM VM 48-QFN |
| ISL6401CB-T | IC REG CTRLR PWM CM 14-SOIC |
| GCM18DREF | CONN EDGECARD 36POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZL6105ALAFTKR5546 | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| ZL6105ALAFTKR5549 | 制造商:Intersil Corporation 功能描述:ADAPTIVE DIGITAL DC-DC CONTROLLER W/ DRIVERS & I-SHARING FE0 - Tape and Reel |
| ZL6105ALAFTKR5553 | 制造商:Intersil Corporation 功能描述:ADAPTIVE DIGITAL DC-DC CONTROLLER W/ DRIVERS & I-SHARING MOD - Tape and Reel |
| ZL6105ALAFTKR5554 | 制造商:Intersil Corporation 功能描述:ADAPTIVE DIGITAL DC-DC CONTROLLER W/ DRIVERS & I-SHARING MOD - Tape and Reel |
| ZL6105ALAFTR5546 | 功能描述:IC REG CTRLR BUCK PWM VM 36-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。