- 您现在的位置：买卖IC网 > PDF目录1986 > AD9510BCPZ-REEL7 (Analog Devices Inc)IC CLOCK DIST 8OUT PLL 64LFCSP PDF资料下载
参数资料
| 型号： | AD9510BCPZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 33/56页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK DIST 8OUT PLL 64LFCSP |
| 标准包装： | 750 |
| 类型： | 扇出缓冲器（分配），除法器 |
| PLL： | 是 |
| 输入： | 时钟 |
| 输出： | CMOS，LVDS，LVPECL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:8 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 1.2GHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 带卷 (TR) |
| 配用： | AD9510-VCO/PCBZ-ND - BOARD EVALUATION FOR AD9510 AD9510/PCBZ-ND - BOARD EVALUATION FOR AD9510 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Data Sheet
AD9510
Rev. B | Page 39 of 56
SINGLE-CHIP SYNCHRONIZATION
SYNCB—Hardware SYNC
The AD9510 clocks can be synchronized to each other at any
time. The outputs of the clocks are forced into a known state
with respect to each other and then allowed to continue clocking
from that state in synchronicity. Before a synchronization is
done, the FUNCTION Pin must be set to act as the SYNCB:
Register 0x58[6:5] = 01b input (Register 0x58[6:5] = 01b).
Synchronization is done by forcing the FUNCTION pin low,
creating a SYNCB signal and then releasing it.
See the SYNCB: Register 0x58[6:5] = 01b section for a more
detailed description of what happens when the SYNCB:
Register 0x58[6:5] = 01b signal is issued.
Soft SYNC—Register 0x58[2]
A soft SYNC can be issued by means of a bit in Registers 0x58[2].
This soft SYNC works the same as the SYNCB, except that the
polarity is reversed. A 1 written to this bit forces the clock outputs
into a known state with respect to each other. When a 0 is
subsequently written to this bit, the clock outputs continue
clocking from that state in synchronicity.
MULTICHIP SYNCHRONIZATION
The AD9510 provides a means of synchronizing two or more
AD9510s. This is not an active synchronization; it requires user
monitoring and action. The arrangement of two AD9510s to be
synchronized is shown in Figure 43.
Synchronization of two or more AD9510s requires a fast clock
and a slow clock. The fast clock can be up to 1 GHz and can be
the clock driving the master AD9510 CLK1 input or one of the
outputs of the master. The fast clock acts as the input to the
distribution section of the slave AD9510 and is connected to its
CLK1 input. The PLL can be used on the master, but the slave
PLL is not used.
The slow clock is the clock that is synchronized across the two
chips. This clock must be no faster than one-fourth of the fast
clock, and no greater than 250 MHz. The slow clock is taken
from one of the outputs of the master AD9510 and acts as the
REFIN (or CLK2) input to the slave AD9510. One of the outputs
of the slave must provide this same frequency back to the CLK2
(or REFIN) input of the slave.
Multichip synchronization is enabled by writing
Register 0x58[0] = 1 on the slave AD9510. When this bit is set,
the STATUS pin becomes the output for the SYNC signal. A low
signal indicates an in-sync condition, and a high indicates an
out-of-sync condition.
Register 0x58[1] selects the number of fast clock cycles that are
the maximum separation of the slow clock edges that are con-
sidered synchronized. When Register 0x58[1] = 0 (default), the
slow clock edges must be coincident within 1 to 1.5 high speed
clock cycles. If the coincidence of the slow clock edges is closer
than this amount, the SYNC flag stays low. If the coincidence of
the slow clock edges is greater than this amount, the SYNC flag
is set high. When Register 0x58[1] = 1b, the amount of coincidence
required is 0.5 fast clock cycles to 1 fast clock cycles.
Whenever the SYNC flag is set high, indicating an out-of-sync
condition, a SYNCB signal applied simultaneously at the
FUNCTION pins of both AD9510s brings the slow clocks into
synchronization.
Figure 43. Multichip Synchronization
05046-039
AD9510
MASTER
FAST CLOCK
<1GHz
SLOW CLOCK
<250MHz
AD9510
SLAVE
FAST CLOCK
<1GHz
SLOW
CLOCK
<250MHz
SYNC
DETECT
CLK2
REFIN
OUTY
OUTM
OUTN
FSYNC
STATUS
(SYNC)
FUNCTION
(SYNCB)
FUNCTION
(SYNCB)
SYNCB
CLK1
相关PDF资料 |
PDF描述 |
|---|---|
| AD9511BCPZ-REEL7 | IC CLOCK DIST 5OUT PLL 48LFCSP |
| AD9512UCPZ-EP-R7 | IC CLOCK DIST 5OUT PLL 48LFCSP |
| AD9512UCPZ-EP | IC CLOCK DIST 5OUT PLL 48LFCSP |
| AD9513BCPZ-REEL7 | IC CLOCK DIST 3OUT PLL 32LFCSP |
| AD9514BCPZ-REEL7 | IC CLOCK DIST 3OUT PLL 32LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9510-VCO/PCB | 制造商:Analog Devices 功能描述:EVAL BD FOR 1.2 GHZ CLOCK DISTRIBUTION IC, PLL CORE, DIVIDER - Bulk 制造商:Analog Devices 功能描述:IC ((NS)) |
| AD9510-VCO/PCBZ | 功能描述:BOARD EVALUATION FOR AD9510 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| AD9511 | 制造商:AD 制造商全称:Analog Devices 功能描述:1.2 GHz Clock Distribution IC, PLL Core, Dividers, Delay Adjust, Five Outputs |
| AD9511/PCB | 制造商:Analog Devices 功能描述:1.2 GHZ CLOCK DISTRIBUTION IC, PLL CORE,DIVIDERS, DELAY ADJUST, FIVE OUTPUTS 制造商:Analog Devices 功能描述:EVAL BD FOR AD9511 1.2 GHZ CLOCK DISTRIBUTION IC, PLL CORE,D - Bulk |
| AD9511BCPZ | 功能描述:IC CLOCK DIST 5OUT PLL 48LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:1,000 系列:Precision Edge® 类型:时钟/频率合成器 PLL:无 输入:CML，PECL 输出:CML 电路数:1 比率 - 输入:输出:2:1 差分 - 输入:输出:是/是 频率 - 最大:10.7GHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘，16-MLF? 供应商设备封装:16-MLF?（3x3） 包装:带卷 (TR) 其它名称:SY58052UMGTRSY58052UMGTR-ND |
发布紧急采购，3分钟左右您将得到回复。