- 您现在的位置：买卖IC网 > PDF目录1194 > ADP1043AFB100EVALZ (Analog Devices Inc)BOARD EVALUATION ADP1043A 100W PDF资料下载
参数资料
| 型号： | ADP1043AFB100EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 23/72页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION ADP1043A 100W |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 已用 IC / 零件： | ADP1043A |
| 主要属性： | * |
| 次要属性： | * |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
ADP1043A
CS2 Pin
The user sets the full-scale (FS) voltage drop—37.5 mV,
75 mV, or 150 mV—that is present across the R SENSE resistor
by programming Register 0x23, Bits[7:6].
The CS2 ADC has an input range of 250 mV. The resolution is
12 bits, which means that the LSB size is 250 mV/4096 = 61.04 μV.
The user is limited to an input range of 215 mV.
The equation to calculate the ADC code at a certain voltage
(V X ) is given by the following formula:
ADC Code = V X /250 mV × 4096
For example, when there is 150 mV on the input of the ADC
ADC Code = 150 mV/250 mV × 4096
ADC Code = 2457
Therefore, to convert the CS2 value reading to a real current,
use the following formula:
I OUT = ( CS2_Value /2457) × ( FS / R SENSE )
where:
FS is the full-scale voltage drop (37.5 mV, 75 mV, or 150 mV).
R SENSE is the sense resistor value.
For example, if CS2_Value = 1520, R SENSE = 20 mΩ, and
FS = 150 mV, the real current is calculated as follows:
I OUT = (1520/2457) × (150 mV/20 mΩ)
FIRST FLAG FAULT ID AND VALUE REGISTERS
When the ADP1043A registers several fault conditions, it stores
the value of the first fault in a dedicated register. For example, if
the overtemperature (OTP) fault is registered, followed by an
OVP fault, the OTP flag is stored in the first flag ID register
(Register 0x10). This register gives the user more information
for fault diagnosis than a simple flag. The contents of this register
are latched, meaning that they are stored until read by the user.
The contents are also reset by a PSON signal.
If a flag is set to be ignored, it does not appear in the first flag
register.
EXTERNAL FLAG INPUT (FLAGIN PIN)
The FLAGIN pin can be used to send an external fault
signal into the ADP1043A. The reaction to this flag can
be programmed in the same way as the internal flags.
TEMPERATURE READINGS (RTD PIN)
The RTD pin is set up for use with an external 100 kΩ negative
temperature coefficient (NTC) thermistor. The RTD pin has an
internal 10.8 μA current source. Therefore, with a 100 kΩ therm-
istor, the voltage on the RTD pin is 1 V at 25°C. An ADC on the
ADP1043A monitors the voltage on the RTD pin.
10μA
I OUT = 4.64 A
POWER READINGS
The output power value register (Register 0x19) is the product
of the VS3 voltage value and the CS2 current value. Therefore,
100k ?
NTC
RTD
RTD
ADC
RTD TEMPERATURE
VALUE REGISTER
REG 0x1A[15:4]
OTP
THRESHOLD
REG 0x2F[7:0]
OTP
FLAG
FLAGS
a combination of the formulas in the Voltage Readings section
and the CS2 Pin section is used to calculate the power reading
in watts. This register is a 16-bit word. It multiplies two 12-bit
numbers and discards the eight LSBs.
P OUT = ( V OUT ) × ( I OUT )
For example,
P OUT = (12 V) × (4.64 A) = 55.68 W
POWER MONITORING ACCURACY
The ADP1043A power monitoring accuracy is specified relative
to the full-scale range of the signal that it is measuring.
Figure 28. RTD Pin Internal Details
The output of the RTD ADC is linearly proportional to the
voltage on the RTD pin. However, thermistors exhibit a non-
linear function of resistance vs. temperature. Therefore, it is
necessary to perform some postprocessing on the RTD ADC
reading to accurately read the temperature. This postprocessing
can be in the form of a lookup table or polynomial equation to
match the specific NTC being used.
OVERTEMPERATURE PROTECTION (OTP)
If the temperature sensed at the RTD pin exceeds the program-
mable threshold, the OTP flag is set. The hysteresis on this flag
is 16 mV (see Register 0x2F in Table 43 for details). The response
to the OTP flag is programmable.
The RTD trim is required to make accurate temperature readings
at the lower end of the RTD ADC range. This results in a more
accurate measurement for determining the OTP threshold (see
the RTD/OTP Trim section).
Rev. 0 | Page 23 of 72
相关PDF资料 |
PDF描述 |
|---|---|
| ADP1046-100-EVALZ | BOARD EVAL FOR ADP1046-100 |
| ADP1048-600-EVALZ | BOARD EVAL ADP1048-600 |
| ADP190CB-EVALZ | BOARD EVAL ADP190 |
| ADP191CB-EVALZ | EVAL BOARD FOR ADP191 |
| ADP194CB-EVALZ | BOARD EVAL FOR ADP194ACBZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1043AIF300EVALZ | 制造商:Analog Devices 功能描述:ADP1043A 300W EVALUATION BOARD - Boxed Product (Development Kits) |
| ADP1043A-USB-Z | 功能描述:EVAL BOARD DIG POWER SUPPLY RoHS:是 类别:编程器，开发系统 >> 配件 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 标准包装:1 系列:- 附件类型:USB 至 1-Wire? RJ11 适配器 适用于相关产品:1-Wire? 设备 产品目录页面:1429 (CN2011-ZH PDF) |
| ADP1043-EVALZ | 制造商:Analog Devices 功能描述:EVALUATION BOARDS - Bulk |
| ADP1043FB100-EVALZ | 制造商:Analog Devices 功能描述:ADP1043 100W EVALUATION BOARD |
| ADP1045ACPZ-RL | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。