参数资料
型号: COP8CCR9KMT8
厂商: National Semiconductor
文件页数: 74/111页
文件大小: 0K
描述: IC MCU EEPROM 8BIT 32K 56-TSSOP
标准包装: 34
系列: COP8™ 8C
核心处理器: COP8
芯体尺寸: 8-位
速度: 20MHz
连通性: Microwire/Plus(SPI),UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 49
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
RAM 容量: 1K x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
数据转换器: A/D 16x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 56-TFSOP(0.240",6.10mm 宽)
包装: 管件
其它名称: *COP8CCR9KMT8
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
5.13.7 BAUD CLOCK GENERATION
The clock inputs to the transmitter and receiver sections of the USART can be individually selected to
come either from an external source at the CKX pin (port L, pin L1) or from a source selected in the PSR
and BAUD registers. Internally, the basic baud clock is created from the MCLK through a two-stage divider
chain consisting of a 1-16 (increments of 0.5) prescaler and an 11-bit binary counter (Figure 5-18). The
divide factors are specified through two read/write registers shown in Figure 5-19. Note that the 11-bit
Baud Rate Divisor spills over into the Prescaler Select Register (PSR). PSR is cleared upon reset.
As shown in Table 5-17, a Prescaler Factor of 0 corresponds to NO CLOCK. This condition is the USART
power down mode where the USART clock is turned off for power saving purpose. The user must also
turn the USART clock off when a different baud rate is chosen.
The correspondences between the 5-bit Prescaler Select and Prescaler factors are shown in Table 5-17.
There are many ways to calculate the two divisor factors, but one particularly effective method would be to
achieve a 1.8432 MHz frequency coming out of the first stage. The 1.8432 MHz prescaler output is then
used to drive the software programmable baud rate counter to create a 16x clock for the following baud
rates: 110, 134.5, 150, 300, 600, 1200, 1800, 2400, 3600, 4800, 7200, 9600, 19200 and 38400 (Table 5-
16). Other baud rates may be created by using appropriate divisors. The 16x clock is then divided by 16 to
provide the rate for the serial shift registers of the transmitter and receiver.
Table 5-16. Baud Rate Divisors
(1.8432 MHz Prescaler Output)(1)
Baud Rate
Divisor
1 (N-1)
110 (110.03)
1046
134.5 (134.58)
855
150
767
300
383
600
191
1200
95
1800
63
2400
47
3600
31
4800
23
7200
15
9600
11
19200
5
38400
2
(1)
The entries in Table 5-16 assume a prescaler output of 1.8432 MHz.
In asynchronous mode the baud rate could be as high as 1250k.
Figure 5-18. USART BAUD Clock Generation
Copyright 2000–2013, Texas Instruments Incorporated
Functional Description
65
Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9
相关PDF资料
PDF描述
COP8SAA716M8/NOPB IC MCU OTP 8BIT 1K 16-SOIC
CP2101-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2103-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2104-F03-GM IC SGL USB-TO-UART BRIDGE 24QFN
CP2105-F01-GM IC SGL USB-DL UART BRIDGE 24QFN
相关代理商/技术参数
参数描述
COP8CCR9LVA7 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
COP8CCR9LVA7/63 制造商:Texas Instruments 功能描述:
COP8CCR9LVA7/63SN 功能描述:闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
COP8CCR9LVA7/NOPB 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
COP8CCR9LVA763SN 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 5V 68-Pin PLCC