- 您现在的位置：买卖IC网 > PDF目录1908 > COP8CCR9KMT8 (National Semiconductor)IC MCU EEPROM 8BIT 32K 56-TSSOP PDF资料下载
参数资料
| 型号： | COP8CCR9KMT8 |
| 厂商： | National Semiconductor |
| 文件页数： | 86/111页 |
| 文件大小： | 0K |
| 描述： | IC MCU EEPROM 8BIT 32K 56-TSSOP |
| 标准包装： | 34 |
| 系列： | COP8™ 8C |
| 核心处理器： | COP8 |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 连通性： | Microwire/Plus（SPI），UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 49 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 16x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-TFSOP（0.240"，6.10mm 宽） |
| 包装： | 管件 |
| 其它名称： | *COP8CCR9KMT8 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页当前第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
5.15.3 VIS INSTRUCTION
The general interrupt service routine, which starts at address 00FF Hex, must be capable of handling all
types of interrupts. The VIS instruction, together with an interrupt vector table, directs the device to the
specific interrupt handling routine based on the cause of the interrupt.
VIS is a single-byte instruction, typically used at the very beginning of the general interrupt service routine
at address 00FF Hex, or shortly after that point, just after the code used for context switching. The VIS
instruction determines which enabled and pending interrupt has the highest priority, and causes an indirect
jump to the address corresponding to that interrupt source. The jump addresses (vectors) for all possible
interrupts sources are stored in a vector table.
The vector table may be as long as 32 bytes (maximum of 16 vectors) and resides at the top of the 256-
byte block containing the VIS instruction. However, if the VIS instruction is at the very top of a 256-byte
block (such as at 00FF Hex), the vector table resides at the top of the next 256-byte block. Thus, if the
VIS instruction is located somewhere between 00FF and 01DF Hex (the usual case), the vector table is
located between addresses 01E0 and 01FF Hex. If the VIS instruction is located between 01FF and 02DF
Hex, then the vector table is located between addresses 02E0 and 02FF Hex, and so on.
Each vector is 15 bits long and points to the beginning of a specific interrupt service routine somewhere in
the 32-kbyte memory space. Each vector occupies two bytes of the vector table, with the higher-order byte
at the lower address. The vectors are arranged in order of interrupt priority. The vector of the maskable
interrupt with the lowest rank is located to 0yE0 (higher-order byte) and 0yE1 (lower-order byte). The next
priority interrupt is located at 0yE2 and 0yE3, and so forth in increasing rank. The Software Trap has the
highest rand and its vector is always located at 0yFE and 0yFF. The number of interrupts which can
become active defines the size of the table.
Table 5-27 shows the types of interrupts, the interrupt arbitration ranking, and the locations of the
corresponding vectors in the vector table.
The vector table should be filled by the user with the memory locations of the specific interrupt service
routines. For example, if the Software Trap routine is located at 0310 Hex, then the vector location 0yFE
and -0yFF should contain the data 03 and 10 Hex, respectively. When a Software Trap interrupt occurs
and the VIS instruction is executed, the program jumps to the address specified in the vector table.
The interrupt sources in the vector table are listed in order of rank, from highest to lowest priority. If two or
more enabled and pending interrupts are detected at the same time, the one with the highest priority is
serviced first. Upon return from the interrupt service routine, the next highest-level pending interrupt is
serviced.
If the VIS instruction is executed, but no interrupts are enabled and pending, the lowest-priority interrupt
vector is used, and a jump is made to the corresponding address in the vector table. This is an unusual
occurrence and may be the result of an error. It can legitimately result from a change in the enable bits or
pending flags prior to the execution of the VIS instruction, such as executing a single cycle instruction
which clears an enable flag at the same time that the pending flag is set. It can also result, however, from
inadvertent execution of the VIS command outside of the context of an interrupt.
The default VIS interrupt vector can be useful for applications in which time critical interrupts can occur
during the servicing of another interrupt. Rather than restoring the program context (A, B, X, etc.) and
executing the RETI instruction, an interrupt service routine can be terminated by returning to the VIS
instruction. In this case, interrupts will be serviced in turn until no further interrupts are pending and the
default VIS routine is started. After testing the GIE bit to ensure that execution is not erroneous, the
routine should restore the program context and execute the RETI to return to the interrupted program.
This technique can save up to fifty instruction cycles (tC), or more, (25 s at 10 MHz oscillator) of latency
for pending interrupts with a penalty of fewer than ten instruction cycles if no further interrupts are
pending.
76
Functional Description
Copyright 2000–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| COP8SAA716M8/NOPB | IC MCU OTP 8BIT 1K 16-SOIC |
| CP2101-GMR | IC CTRLR BRIDGE USB-UART 28MLP |
| CP2103-GMR | IC CTRLR BRIDGE USB-UART 28MLP |
| CP2104-F03-GM | IC SGL USB-TO-UART BRIDGE 24QFN |
| CP2105-F01-GM | IC SGL USB-DL UART BRIDGE 24QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| COP8CCR9LVA7 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| COP8CCR9LVA7/63 | 制造商:Texas Instruments 功能描述: |
| COP8CCR9LVA7/63SN | 功能描述:闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| COP8CCR9LVA7/NOPB | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| COP8CCR9LVA763SN | 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 5V 68-Pin PLCC |
发布紧急采购，3分钟左右您将得到回复。