COP8CCR9KMT8 (National) PDF资料下载 Datasheet(88/111 页)

您现在的位置：买卖IC网 > PDF目录1908 > COP8CCR9KMT8 (National Semiconductor)IC MCU EEPROM 8BIT 32K 56-TSSOP PDF资料下载

参数资料

型号：	COP8CCR9KMT8
厂商：	National Semiconductor
文件页数：	88/111页
文件大小：	0K
描述：	IC MCU EEPROM 8BIT 32K 56-TSSOP
标准包装：	34
系列：	COP8™ 8C
核心处理器：	COP8
芯体尺寸：	8-位
速度：	20MHz
连通性：	Microwire/Plus（SPI），UART/USART
外围设备：	欠压检测/复位，POR，PWM，WDT
输入/输出数：	49
程序存储器容量：	32KB（32K x 8）
程序存储器类型：	闪存
RAM 容量：	1K x 8
电压 - 电源 (Vcc/Vdd)：	2.7 V ~ 5.5 V
数据转换器：	A/D 16x10b
振荡器型：	内部
工作温度：	-40°C ~ 85°C
封装/外壳：	56-TFSOP（0.240"，6.10mm 宽）
包装：	管件
其它名称：	*COP8CCR9KMT8

SNOS535I – OCTOBER 2000 – REVISED MARCH 2013

Figure 5-24. VIS Operation

5.15.4 NON-MASKABLE INTERRUPT

5.15.4.1 Pending Flag

There is a pending flag bit associated with the non-maskable Software Trap interrupt, called STPND. This

pending flag is not memory-mapped and cannot be accessed directly by the software.

The pending flag is reset to zero when a device Reset occurs. When the non-maskable interrupt occurs,

the associated pending bit is set to 1. The interrupt service routine should contain an RPND instruction to

reset the pending flag to zero. The RPND instruction always resets the STPND flag.

5.15.4.2 Software Trap

The Software Trap is a special kind of non-maskable interrupt which occurs when the INTR instruction

(used to acknowledge interrupts) is fetched from program memory and placed in the instruction register.

This can happen in a variety of ways, usually because of an error condition. Some examples of causes

are listed below.

If the program counter incorrectly points to a memory location beyond the programmed Flash memory

space, the unused memory location returns zeros which is interpreted as the INTR instruction.

If the stack is popped beyond the allowed limit (address 06F Hex), a 7FFF will be loaded into the PC.

Since the Option Register resides at this location, and to maintain the integrity of the stack overpop

protection, the Flash memory will return a zero on an instruction fetch and a software trap will be

triggered.

A Software Trap can be triggered by a temporary hardware condition such as a brownout or power supply

glitch.

The Software Trap has the highest priority of all interrupts. When a Software Trap occurs, the STPND bit

is set. The GIE bit is not affected and the pending bit (not accessible by the user) is used to inhibit other

interrupts and to direct the program to the ST service routine with the VIS instruction. Nothing can interrupt

a Software Trap service routine except for another Software Trap. The STPND can be reset only by the

RPND instruction or a chip Reset.

Functional Description

相关代理商/技术参数	参数描述
COP8CCR9LVA7	功能描述:8位微控制器 -MCU RoHS:否制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
COP8CCR9LVA7/63	制造商:Texas Instruments 功能描述:
COP8CCR9LVA7/63SN	功能描述:闪存 RoHS:否制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
COP8CCR9LVA7/NOPB	功能描述:8位微控制器 -MCU RoHS:否制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
COP8CCR9LVA763SN	制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 5V 68-Pin PLCC

发布紧急采购，3分钟左右您将得到回复。

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购