- 您现在的位置：买卖IC网 > PDF目录381697 > DDRSDRAM (SAMSUNG SEMICONDUCTOR CO. LTD.) DDR SDRAM Specification Version 0.61 PDF资料下载
参数资料
| 型号： | DDRSDRAM |
| 厂商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | DDR SDRAM Specification Version 0.61 |
| 中文描述： | DDR SDRAM的规格版本0.61 |
| 文件页数： | 27/49页 |
| 文件大小： | 750K |
| 代理商： | DDRSDRAM |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
- 27 of 63 -
REV. 0.61 August 9. '99
128Mb DDR SDRAM
Target
3. For a Write with autoprecharge command, a new Bank Activate command may be issued to the same
bank after tWR+tRP where tWR+tRP starts on the falling DQS edge that strobed in the last valid data and
ends on the rising clock edge that strobes in the Bank Activate command. During write with
autoprecharge, the initiation of the internal precharge occurs at the same time as the earliest possible
external Precharge command without interrupting the Write burst as described in 1 above.
4. In all cases, a Precharge operation cannot be initiated unless tRAS(min) [minimum Bank Activate to
Precharge time] has been satisfied. This includes Write with autoprecharge commands where tRAS(min)
must still be satisfied such that a Write with autoprecharge command has the same timing as a Write
command followed by the earliest possible Precharge command which does not interrupt the burst.
3.3.9 Burst Stop
The burst stop command is initiated by having RAS and CAS high with CS and WE low at the rising edge of
the clock(CK). The burst stop command has the fewest restrictions making it the easiest method to use when
terminating a burst read operation before it has been completed. When the burst stop command is issued dur-
ing a burst read cycle, the pair of data and DQS(Data Strobe) go to a high impedance state after a delay which
is equal to the CAS latency set in the mode register. The burst stop command, however, is not supported dur-
ing a write burst operation.
Command
< Burst Length=4, CAS Latency= 2, 2.5 >
READ A
Burst Stop
NOP
NOP
NOP
NOP
NOP
NOP
NOP
DQS
DQ
′
s
CAS Latency=2
Dout 0 Dout 1
DQS
DQ
′
s
CAS Latency=2.5
The burst ends after a delay equal to the CAS latency.
Dout 0 Dout 1
2
0
1
5
3
4
8
6
7
CK
CK
The Burst Stop command is a mandatory feature for DDR SDRAMs. The following functionality is required:
1. The BST command may only be issued on the rising edge of the input clock, CK.
2. BST is only a valid command during Read bursts.
3. BST during a Write burst is undefined and shall not be used.
4. BST applies to all burst lengths.
5. BST is an undefined command during Read with autoprecharge and shall not be used.
Figure 17. Burst stop timing
相关PDF资料 |
PDF描述 |
|---|---|
| DDTA113TCA-7-F | PNP PRE-BIASED SMALL SIGNAL SOT-23 SURFACE MOUNT TRANSISTOR |
| DDTA114TCA-7-F | PNP PRE-BIASED SMALL SIGNAL SOT-23 SURFACE MOUNT TRANSISTOR |
| DDTA115TCA-7-F | PNP PRE-BIASED SMALL SIGNAL SOT-23 SURFACE MOUNT TRANSISTOR |
| DDTA123TCA-7-F | PNP PRE-BIASED SMALL SIGNAL SOT-23 SURFACE MOUNT TRANSISTOR |
| DDTA124TCA-7-F | PNP PRE-BIASED SMALL SIGNAL SOT-23 SURFACE MOUNT TRANSISTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DDRSDRAM1111 | 制造商:SAMSUNG 制造商全称:Samsung semiconductor 功能描述:DDR SDRAM Specification Version 1.0 |
| DDR-SJE-Q2 | 制造商:DOMINANT 制造商全称:DOMINANT Semiconductors 功能描述:LED Colored Resin |
| DDR-SJE-Q2R-1 | 制造商:DOMINANT 制造商全称:DOMINANT Semiconductors 功能描述:LED Colored Resin |
| DDR-SJE-R1 | 制造商:DOMINANT 制造商全称:DOMINANT Semiconductors 功能描述:LED Colored Resin |
| DDR-SJE-R2 | 制造商:DOMINANT 制造商全称:DOMINANT Semiconductors 功能描述:LED Colored Resin |
发布紧急采购，3分钟左右您将得到回复。