- 您现在的位置：买卖IC网 > PDF目录16440 > EVAL-ADE5169EBZ-2 (Analog Devices Inc)BOARD EVALUATION FOR AD5169 PDF资料下载
参数资料
| 型号： | EVAL-ADE5169EBZ-2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 127/156页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD5169 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是 |
| 已用 IC / 零件： | ADE5169 |
| 主要属性： | 用于汇编语言和 C 代码的 IAR 工具 |
| 次要属性： | 隔离和非隔离输出选项 |
| 已供物品： | 板，软件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页当前第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页
Data Sheet
Table 137. Leap Years—Rollover After 29 Days
YEAR Register Estimated Year
0d04 2004
0d08 2008
0d12 2012
0d16 2016
0d20 2020
0d24 2024
0d28 2028
0d32 2032
0d36 2036
0d40 2040
0d44 2044
0d48 2048
0d52 2052
0d56 2056
0d60 2060
0d64 2064
0d68 2068
0d72 2072
0d76 2076
0d80 2080
0d84 2084
0d88 2088
0d92 2092
0d96 2096
RTC INTERRUPTS
The RTC alarm and interval timer interrupts are enabled by
setting the ETI bit in the Interrupt Enable and Priority 2 SFR
(IEIP2, Address 0xA9[2]). When an alarm or interval timer
event occurs, the corresponding flag is set and a pending RTC
interrupt is generated. If the RTC interrupt is enabled, the program
vectors to the RTC interrupt address, and the corresponding
RTC flag can be cleared in software. Moving to the RTC interrupt
address alone does not automatically clear the flag. To success-
fully acknowledge the interrupt event, the flag must be cleared
by software. If the RTC interrupt is disabled when the event occurs,
the pending interrupt remains until the corresponding RTC flag
is cleared. Therefore, the ALFLAG and ITFLAG flags (Bit 6 and
Bit 2, respectively, in the RTC configuration SFR (TIMECON,
Address 0xA1)) drive the RTC interrupt and should be managed
by the user to keep track of the RTC events.
ADE5166/ADE5169/ADE5566/ADE5569
Note that, if the ADE5166/ADE5169/ADE5566/ADE5569 are
awakened by an RTC event, either the ALFLAG or ITFLAG,
then the pending RTC interrupt, must be serviced before the
devices can go back to sleep again. The ADE5166/ADE5169/
ADE5566/ADE5569 keep waking up until this interrupt has
been serviced.
Interval Timer Alarm
The RTC can be used as an interval timer. When the interval timer
is enabled by setting ITEN (TIMECON[1]), the interval timer
clock source selected by the ITS1 and ITS0 bits (TIMECON[5:4]) is
passed through to an 8-bit counter. This counter increments on
every interval timer clock pulse until the 8-bit counter is equal to
the value in the alarm interval register. Then an alarm event is
generated, setting the ITFLAG bit (TIMECON[2]) and creating
a pending RTC interrupt. If the SIT bit (TIMECON[3]) is cleared,
the 8-bit counter is cleared and starts counting again. If the SIT
bit is set, the 8-bit counter is held in reset after the alarm occurs.
Take care when changing the interval timer timebase. The
recommended procedure is as follows:
1. If the INTVAL register is to be modified, write to the INTVAL
register first. Then wait for one 128 Hz clock cycle to syn-
chronize with the RTC, 64,000 cycles at a 4.096 MHz
instruction cycle clock.
2. Disable the interval timer by clearing ITEN (TIMECON[1]).
Then wait for one 128 Hz clock cycle to synchronize with the
RTC, 64,000 cycles at a 4.096 MHz instruction cycle clock.
3. Read the TIMECON SFR to ensure that the ITEN bit is
cleared. If it is not, wait for another 128 Hz clock cycle.
4. Set the timebase bits, ITS1 and ITS0 (TIMECON[5:4]) to
configure the interval. Wait for a 128 Hz clock cycle for this
change to take effect.
RTC Wake-Up Alarm
The RTC can be used with an alarm to wake up periodically. The
alarm registers (AL_SEC, AL_MIN, AL_HOUR, AL_DAY, and
AL_DATE) should be set to the specific time that the alarm event
is required, and the corresponding ALxxx_EN bits must be set in
the RTC Configuration 2 SFR (TIMECON2, Address 0xA2). The
enabled alarm registers are then compared to their respective
RTC registers (SEC, MIN, HOUR, DAY, and DATE). When all
enabled alarms match their corresponding RTC registers, the alarm
flag is set, and a pending interrupt is generated. If the alarm flag
(ALFLAG, TIMECON[6]) is enabled, an RTC interrupt occurs
and the program vectors to the RTC interrupt address.
Rev. D | Page 127 of 156
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J1M-EX | CONVERTER MINIMOD DC/DC 10V 75W |
| VE-21M-EX | CONVERTER MOD DC/DC 10V 75W |
| VE-21R-EX | CONVERTER MOD DC/DC 7.5V 75W |
| AD9912A/PCBZ | BOARD EVALUATION FOR AD9912 |
| H1KXH-2636M | IDC CABLE - HPK26H/AE26M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADE5169F62EBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR ADE5169 - Boxed Product (Development Kits) 制造商:Rochester Electronics LLC 功能描述: |
| EVAL-ADE5569F62EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| EVAL-ADE7169EBZ-2 | 功能描述:BOARD EVALUATION FOR ADE7169F16 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| EVAL-ADE7169F16EB | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver |
| EVAL-ADE7169F16EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For ADE7169 制造商:Analog Devices 功能描述:EVAL BD FOR ADE7169 - Bulk |
发布紧急采购，3分钟左右您将得到回复。