- 您现在的位置：买卖IC网 > PDF目录16440 > EVAL-ADE5169EBZ-2 (Analog Devices Inc)BOARD EVALUATION FOR AD5169 PDF资料下载
参数资料
| 型号： | EVAL-ADE5169EBZ-2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 146/156页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD5169 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是 |
| 已用 IC / 零件： | ADE5169 |
| 主要属性： | 用于汇编语言和 C 代码的 IAR 工具 |
| 次要属性： | 隔离和非隔离输出选项 |
| 已供物品： | 板，软件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页当前第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页
ADE5166/ADE5169/ADE5566/ADE5569
I 2 C-COMPATIBLE INTERFACE
The ADE5166/ADE5169/ADE5566/ADE5569 support a fully
licensed I 2 C interface. The I 2 C interface is implemented as a full
Data Sheet
The bit rate is defined in the I2CMOD SFR (Address 0xE8)
as follows:
hardware master.
SDATA (P0.4/MOSI/SDATA) is the data I/O pin, and SCLK
f SCLK =
f CORE
16 × 2 I 2 CR [ 1 : 0 ]
(P0.6/SCLK/T0) is the serial clock. These two pins are shared with
the MOSI and SCLK pins of the on-chip SPI interface. Therefore,
the user can enable only one interface at a time on these pins. The
SCPS bit in the configuration SFR (CFG, Address 0xAF[5]) selects
which peripheral is active.
The two pins used for data transfer, SDATA and SCLK, are
configured in a wire-AND format that allows arbitration in a
SLAVE ADDRESSES
The I 2 C slave address SFR (I2CADR, Address 0xE9) contains
the slave device ID. The LSB of this register contains a read/write
request. A write to this SFR starts the I 2 C communication.
I 2 C REGISTERS
The I 2 C peripheral interface consists of five SFRs.
multimaster system.
?
I2CMOD
The transfer sequence of an I C system consists of a master device
2
initiating a transfer by generating a start condition while the bus
is idle. The master transmits the address of the slave device and
the direction of the data transfer in the initial address transfer. If
the slave acknowledges, the data transfer is initiated. This continues
until the master issues a stop condition and the bus becomes idle.
SERIAL CLOCK GENERATION
The I 2 C master in the system generates the serial clock for a
transfer. The master channel can be configured to operate in
fast mode (256 kHz) or in standard mode (32 kHz).
Table 156. I 2 C SFR List
? SPI2CSTAT
? I2CADR
? SPI2CTx
? SPI2CRx
Because the SPI and I 2 C serial interfaces share the same pins,
they also share the same SFRs, such as the SPI2CTx and SPI2CRx
SFRs. In addition, the I2CMOD, I2CADR, and SPI2CSTAT SFRs
are shared with the SPIMOD1, SPIMOD2, and SPISTAT SFRs,
respectively.
SFR Address
0x9A
0x9B
0xE8
0xE9
0xEA
Mnemonic
SPI2CTx
SPI2CRx
I2CMOD
I2CADR
SPI2CSTAT
R/W
W
R
R/W
R/W
R/W
Length
8
8
8
8
8
Default
0
0
0
0
Description
SPI/I 2 C transmit buffer (see Table 151).
SPI/I 2 C receive buffer (see Table 152).
I 2 C mode (see Table 157).
I 2 C slave address (see Table 158).
I 2 C interrupt status (see Table 159).
Table 157. I 2 C Mode SFR (I2CMOD, Address 0xE8)
Bit
7
Bit Address
0xEF
Mnemonic
I2CEN
Default
0
Description
I 2 C enable bit. When this bit is set to Logic 1, the I 2 C interface is enabled. A write to the
I2CADR SFR (Address 0xE9) starts a communication.
[6:5]
0xEE to 0xED
I2CR
00
I 2 C SCLK frequency.
I2CR
00
01
10
11
Result
f CORE /16 = 256 kHz if f CORE = 4.096 MHz
f CORE /32 = 128 kHz if f CORE = 4.096 MHz
f CORE /64 = 64 kHz if f CORE = 4.096 MHz
f CORE /128 = 32 kHz if f CORE = 4.096 MHz
[4:0]
0xEC to 0xE8
I2CRCT
00000
Configures the length of the I 2 C received FIFO buffer. The I 2 C peripheral stops when
I2CRCT[4:0] + 1 byte have been read, or if an error occurs.
Table 158. I 2 C Slave Address SFR (I2CADR, Address 0xE9)
Bit
[7:1]
0
Mnemonic
I2CSLVADR
I2CR_W
Default
0
0
Description
Address of the I 2 C slave being addressed. Writing to this register starts the I 2 C transmission (read or write).
Command bit for read or write. When this bit is set to Logic 1, a read command is transmitted on the
I 2 C bus. Data from the slave in the SPI2CRx SFR (Address 0x9B) is expected after a command byte.
When this bit is set to Logic 0, a write command is transmitted on the I 2 C bus. Data to the slave is
expected in the SPI2CTx SFR.
Rev. D | Page 146 of 156
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J1M-EX | CONVERTER MINIMOD DC/DC 10V 75W |
| VE-21M-EX | CONVERTER MOD DC/DC 10V 75W |
| VE-21R-EX | CONVERTER MOD DC/DC 7.5V 75W |
| AD9912A/PCBZ | BOARD EVALUATION FOR AD9912 |
| H1KXH-2636M | IDC CABLE - HPK26H/AE26M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADE5169F62EBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR ADE5169 - Boxed Product (Development Kits) 制造商:Rochester Electronics LLC 功能描述: |
| EVAL-ADE5569F62EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| EVAL-ADE7169EBZ-2 | 功能描述:BOARD EVALUATION FOR ADE7169F16 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| EVAL-ADE7169F16EB | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver |
| EVAL-ADE7169F16EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For ADE7169 制造商:Analog Devices 功能描述:EVAL BD FOR ADE7169 - Bulk |
发布紧急采购，3分钟左右您将得到回复。