- 您现在的位置：买卖IC网 > PDF目录16440 > EVAL-ADE5169EBZ-2 (Analog Devices Inc)BOARD EVALUATION FOR AD5169 PDF资料下载
参数资料
| 型号： | EVAL-ADE5169EBZ-2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 73/156页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD5169 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是 |
| 已用 IC / 零件： | ADE5169 |
| 主要属性： | 用于汇编语言和 C 代码的 IAR 工具 |
| 次要属性： | 隔离和非隔离输出选项 |
| 已供物品： | 板，软件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页当前第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页
Data Sheet
ENERGY-TO-FREQUENCY CONVERSION
The ADE5166/ADE5169/ADE5566/ADE5569 also provide two
energy-to-frequency conversions for calibration purposes. After
initial calibration at manufacturing, the manufacturer or end
customer often verifies the energy meter calibration. One conve-
nient way to do this is for the manufacturer to provide an output
frequency that is proportional to the active power, reactive power,
apparent power, or I rms under steady load conditions. This output
frequency can provide a simple single-wire, optically isolated
interface to external calibration equipment. Figure 79 illustrates
the energy-to-frequency conversion in the ADE5166/ADE5169/
ADE5566/ADE5569.
ADE5166/ADE5169/ADE5566/ADE5569
The selection between I rms and apparent power is done by the
VARMSCFCON bit (Bit 3) in the MODE2 register (Address 0x0C).
With this selection, CF2 cannot be proportional to apparent power
if CF1 is proportional to I rms , and CF1 cannot be proportional to
apparent power if CF2 is proportional to I rms .
Pulse Output Characteristic
The pulse output for both DFCs stays low for 90 ms if the pulse
period is longer than 180 ms (5.56 Hz). If the pulse period is
shorter than 180 ms, the duty cycle of the pulse output is 50%.
The pulse output is active low and should preferably be connected
to an LED, as shown in Figure 80.
V DD
MODE2 REGISTER 0x0C
CF
VARMSCFCON CFxSEL[1:0]
I rms
VA
CFxNUM
Figure 80. CF Pulse Output
VAR*
WATT
DFC
÷
CFxDEN
CFx PULSE
OUTPUT
The maximum output frequency with ac input signals at
full scale and CFxNUM = 0x00 and CFxDEN = 0x00 is
approximately 21.1 kHz.
The ADE5166/ADE5169/ADE5566/ADE5569 incorporate two
*AVAILABLE ONLY IN THE ADE5169 AND ADE5569.
Figure 79. Energy-to-Frequency Conversion
Two digital-to-frequency converters (DFC) are used to generate
the pulsed outputs. When WDIV = 0 or 1, the DFC generates a
pulse each time 1 LSB in the energy register is accumulated. An
output pulse is generated when a CFxNUM/CFxDEN number of
pulses are generated at the DFC output. Under steady load con-
ditions, the output frequency is proportional to the active power,
reactive power, apparent power, or I rms , depending on the
CFxSEL bits in the MODE2 register (Address 0x0C).
Both pulse outputs can be enabled or disabled by clearing or
setting the DISCF1 bit (Bit 1) and the DISCF2 bit (Bit 2) in the
MODE1 register (Address 0x0B), respectively.
Both pulse outputs set separate flags in the Interrupt Status 2 SFR
(MIRQSTM, Address 0xDD): CF1 (Bit 6) and CF2 (Bit 7). If the
CF1 enable bit (Bit 6) and CF2 enable bit (Bit 7) in the Interrupt
Enable 2 SFR (MIRQENM, Address 0xDA) are set, the 8052 core
has a pending ADE interrupt. The ADE interrupt stays active
until the CF1 or CF2 status bit is cleared (see the Energy
Measurement Interrupts section).
Pulse Output Configuration
The two pulse output circuits have separate configuration bits
in the MODE2 register (Address 0x0C). Setting the CFxSEL bits
to 0b00, 0b01, or 0b1X configures the DFC to create a pulse output
proportional to active power, reactive power, or apparent power
or I rms , respectively.
registers per DFC, CFxNUM[15:0] and CFxDEN[15:0], to set
the CFx frequency. These unsigned, 16-bit registers can be used
to adjust the CFx frequency to a wide range of values, scaling
the output frequency by 1/2 16 to 1 with a step of 1/2 16 .
If 0 is written to any of these registers, 1 is applied to the register.
The ratio of CFxNUM/CFxDEN should be <1 to ensure proper
operation. If the ratio of the CFxNUM/CFxDEN registers is >1,
the register values are adjusted to a ratio of 1. For example, if the
output frequency is 1.562 kHz, and the content of CFxDEN is 0
(0x000), the output frequency can be set to 6.1 Hz by writing 0xFF
to the CFxDEN register.
ENERGY REGISTER SCALING
The ADE5166/ADE5169/ADE5566/ADE5569 provide measure-
ments of active, reactive, and apparent energy that use separate
paths and filtering for calculation. The difference in data paths can
result in small differences in LSB weight between active, reactive,
and apparent energy registers. These measurements are internally
compensated so that the scaling is nearly one to one. The relation-
ship between these registers is shown in Table 48.
Table 48. Energy Registers Scaling
Line Frequency = 50 Hz Line Frequency = 60 Hz Integrator
Var = 0.9952 × watt Var = 0.9949 × watt Off
VA = 0.9978 × watt VA = 1.0015 × watt Off
Var = 0.9997 × watt Var = 0.9999 × watt On
VA = 0.9977 × watt VA = 1.0015 × watt On
Rev. D | Page 73 of 156
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J1M-EX | CONVERTER MINIMOD DC/DC 10V 75W |
| VE-21M-EX | CONVERTER MOD DC/DC 10V 75W |
| VE-21R-EX | CONVERTER MOD DC/DC 7.5V 75W |
| AD9912A/PCBZ | BOARD EVALUATION FOR AD9912 |
| H1KXH-2636M | IDC CABLE - HPK26H/AE26M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADE5169F62EBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR ADE5169 - Boxed Product (Development Kits) 制造商:Rochester Electronics LLC 功能描述: |
| EVAL-ADE5569F62EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| EVAL-ADE7169EBZ-2 | 功能描述:BOARD EVALUATION FOR ADE7169F16 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| EVAL-ADE7169F16EB | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver |
| EVAL-ADE7169F16EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For ADE7169 制造商:Analog Devices 功能描述:EVAL BD FOR ADE7169 - Bulk |
发布紧急采购，3分钟左右您将得到回复。