- 您现在的位置：买卖IC网 > PDF目录223992 > HY27SA081G1M-VPEB (HYNIX SEMICONDUCTOR INC) 128M X 8 FLASH 1.8V PROM, 12000 ns, PDSO48 PDF资料下载
参数资料
| 型号： | HY27SA081G1M-VPEB |
| 厂商： | HYNIX SEMICONDUCTOR INC |
| 元件分类： | PROM |
| 英文描述： | 128M X 8 FLASH 1.8V PROM, 12000 ns, PDSO48 |
| 封装： | 12 X 17 MM, 0.70 MM HEIGHT, LEAD FREE, WSOP1-48 |
| 文件页数： | 9/45页 |
| 文件大小： | 675K |
| 代理商： | HY27SA081G1M-VPEB |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
Rev 0.3 / May. 2004
17
Preliminary
HY27UA(08/16)1G1M Series
HY27SA(08/16)1G1M Series
1Gbit (128Mx8bit / 64Mx16bit) NAND Flash
Page Program
The Page Program operation is the standard operation to program data to the memory array. The main area of the
memory array is programmed by page, however partial page programming is allowed where any number of bytes (1 to
528) or words (1 to 264) can be programmed.
The max number of consecutive partial page program operations allowed in the same page is one in the main area and
two in the spare area. After exceeding this a Block Erase command must be issued before any further program opera-
tions can take place in that page.
Before starting a Page Program operation a Pointer operation can be performed to point to the area to be pro-
grammed. Refer to the Pointer Operations section and Figure 9 for details.
Each Page Program operation consists of five steps (see Figure 14):
1. one bus cycle is required to setup the Page Program command
2. four bus cycles are then required to input the program address (refer to Table 3)
3. the data is then input (up to 528 Bytes/ 264 Words) and loaded into the Page Buffer
4. one bus cycle is required to issue the confirm command to start the Program/ Erase/Read Controller.
5. The Program/ Erase/Read Controller then programs the data into the array.
Once the program operation has started the Status Register can be read using the Read Status Register command.
During program operations the Status Register will only flag errors for bits set to '1' that have not been successfully
programmed to '0'.
During the program operation, only the Read Status Register and Reset commands will be accepted, all other com-
mands will be ignored.
Once the program operation has completed the Program/ Erase/Read Controller bit SR6 is set to '1' and the Ready/
Busy signal goes High.
The device remains in Read Status Register mode until another valid command is written to the Command Interface.
Note: Before starting a Page Program operation a Pointer operation can be performed. Refer to Pointer section for details.
Figure 14. Page Program Operation
Address Inputs
I/O
80h
Page Program
Setup Code
Data Input
10h
70h
SR0
Confirm
Code
Read Status Register
Busy
tBLBH2
(Program Busy time)
RB
相关PDF资料 |
PDF描述 |
|---|---|
| HY27UA081G1M-TIB | 128M X 8 FLASH 3.3V PROM, 12000 ns, PDSO48 |
| HY27US08121B-TPIS | 64M X 8 FLASH 3.3V PROM, 18 ns, PDSO48 |
| HY27US08121B-FIB | 64M X 8 FLASH 3.3V PROM, 18 ns, PBGA63 |
| HY27US081G1MSES | 128M X 8 FLASH 2.7V PROM, 45 ns, PDSO48 |
| HY27US081G1MTCS | 128M X 8 FLASH 2.7V PROM, 45 ns, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HY27SA161G1M | 制造商:HYNIX 制造商全称:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory |
| HY27SA1G1M | 制造商:HYNIX 制造商全称:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory |
| HY27SAXXX | 制造商:HYNIX 制造商全称:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory |
| HY27SF081G2A | 制造商:HYNIX 制造商全称:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash |
| HY27SF081G2A-F(P) | 制造商:SK Hynix Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。