- 您现在的位置：买卖IC网 > PDF目录67712 > IDT72T6360L6BBGI (INTEGRATED DEVICE TECHNOLOGY INC) SPECIALTY MICROPROCESSOR CIRCUIT, PBGA324 PDF资料下载
参数资料
| 型号： | IDT72T6360L6BBGI |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PBGA324 |
| 封装： | 19 X 19 MM, 1 MM PITCH, PLASTIC, BGA-324 |
| 文件页数： | 41/51页 |
| 文件大小： | 508K |
| 代理商： | IDT72T6360L6BBGI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
46
IDT72T6360 2.5V, SEQUENTIAL FLOW-CONTROL DEVICE
x9, x18, x36 BIT WIDE CONFIGURATION
COMMERCIALANDINDUSTRIAL
TEMPERATURERANGES
OCTOBER 10, 2005
Refer to the IEEE Standard Test Access Port Specification (IEEE Std.
1149.1) for the full state diagram
All state transitions within the TAP controller occur at the rising edge of the
TCLK pulse. The TMS signal level (0 or 1) determines the state progression
that occurs on each TCLK rising edge.
Test-Logic-ResetAlltestlogicisdisabledinthiscontrollerstateenablingthe
normaloperationoftheIC.TheTAPcontrollerstatemachineisdesignedinsuch
awaythat,nomatterwhattheinitialstateofthecontrolleris,theTest-Logic-Reset
state can be entered by holding TMS at high and pulsing TCK five times.
Run-Test-Idle In this controller state, the test logic in the IC is active only if
certaininstructionsarepresent.Forexample,ifaninstructionactivatestheself
test, then it will be executed when the controller enters this state. The test logic
in the IC is idle otherwise.
Select-DR-Scan This is a controller state where the decision to enter the
Data Path or the Select-IR-Scan state is made.
Select-IR-Scan This is a controller state where the decision to enter the
InstructionPathismade.TheControllercanreturntotheTest-Logic-Resetstate
other wise.
Capture-IR In this controller state, the shift register bank in the Instruction
Register parallel loads a pattern of fixed values on the rising edge of TCK. The
last two significant bits are always required to be “01”.
Figure 33. TAP Controller State Diagram
Shift-IR In this controller state, the instruction register gets connected
between TDI and TDO, and the captured pattern gets shifted on each rising
edge of TCK. The instruction available on the TDI pin is also shifted in to the
instruction register. TDO changes on the falling edge of TCK.
Exit1-IRThisisacontrollerstatewhereadecisiontoentereitherthePause-
IR state or Update-IR state is made.
Pause-IR This state is provided in order to allow the shifting of instruction
register to be temporarily halted.
Exit2-DRThis is a controller state where a decision to enter either the Shift-
IR state or Update-IR state is made.
Update-IR In this controller state, the instruction in the instruction register
scanchainislatchedintotheregisteroftheInstructionRegisteroneveryfalling
edgeofTCK.Thisinstructionalsobecomesthecurrentinstructiononceitislatched.
Capture-DR In this controller state, the data is parallel loaded in to the data
registers selected by the current instruction on the rising edge of TCK.
Shift-DR, Exit1-DR, Pause-DR, Exit2-DR and Update-DR These
controller states are similar to the Shift-IR, Exit1-IR, Pause-IR, Exit2-IR and
Update-IR states in the Instruction path.
Test-Logic
Reset
Run-Test/
Idle
1
0
Select-
DR-Scan
Select-
IR-Scan
1
Capture-IR
0
Capture-DR
0
Exit1-DR
1
Pause-DR
0
Exit2-DR
1
Update-DR
1
Exit1-IR
1
Exit2-IR
1
Update-IR
1
0
1
6357 drw47
0
Shift-DR
0
Shift-IR
0
Pause-IR
0
1
Input is
TMS
0
1
NOTES:
1. Five consecutive 1's at TMS will reset the TAP.
2. TAP controller resets automatically upon power-up.
相关PDF资料 |
PDF描述 |
|---|---|
| IDT73210ATC | 73 SERIES, 9-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, CDIP24 |
| IDT73211ATCB | 73 SERIES, 9-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, CDIP24 |
| IDT73210TC | 73 SERIES, 9-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, CDIP24 |
| IDT73211TCB | 73 SERIES, 9-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, CDIP24 |
| IDT73210ATCB | 73 SERIES, 9-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, CDIP24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT72T6360L7-5BB | 功能描述:IC FLOW-CTRL 48BIT 7-5NS 324-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72T6360L7-5BBI | 功能描述:IC FLOW-CTRL 48BIT 7-5NS 324-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72T6480L10BB | 功能描述:IC FLOW-CTRL 48BIT 10NS 324-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72T6480L10BBI | 功能描述:IC FLOW-CTRL 48BIT 10NS 324-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72T6480L7-5BB | 功能描述:IC FLOW-CTRL 48BIT 7-5NS 324-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
发布紧急采购，3分钟左右您将得到回复。