收藏本站
参数资料
型号： M38D59GC-XXXFP
元件分类： 微控制器/微处理器
英文描述： 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80
封装： 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80
文件页数： 91/142页
文件大小： 2004K
代理商： M38D59GC-XXXFP
Rev.3.04
May 20, 2008
Page 52 of 134
REJ03B0158-0304
38D5 Group
LCD DRIVE CONTROL CIRCUIT
The 38D5 Group has the built-in Liquid Crystal Display (LCD)
drive control circuit consisting of the following.
LCD display RAM
Segment output disable register
LCD mode register
Selector
Timing controller
Common driver
Segment driver
Bias control circuit
A maximum of 36 segment output pins and 8 common output
pins can be used.
Up to 256 pixels can be controlled for an LCD display. When the
LCD enable bit is set to “1” after data is set in the LCD mode
register, the segment output disable register, and the LCD display
RAM, the LCD drive control circuit starts reading the display
data automatically, performs the bias control and the duty ratio
control, and displays the data on the LCD panel.
.
Fig. 43 Structure of LCD related registers
Table 12
Maximum number of display pixels at each duty ratio
Duty ratio
Maximum number of display pixels
1
36 dots
or 8 segment LCD 4 digits
2
72 dots
or 8 segment LCD 9 digits
3
108 dots
or 8 segment LCD 13 digits
4
144 dots
or 8 segment LCD 18 digits
8
256 dots
or 8 segment LCD 32 digits
LCD mode register 1
(LM 1 : address 001316)
b7
b0
Duty ratio selection bits
b2b1b0
0 0 0 : 1 (Static)
0 0 1 : 2 (use COM0, COM1)
0 1 0 : 3 (use COM0-COM2)
0 1 1 : 4 (use COM0-COM3)
1 0 0 to 1 1 0 : Not available
1 1 1 : 8 (COM0-COM7)
Bias control bit
0 : 1/3 bias
1 : 1/2 bias
LCD enable bit
0 : LCD OFF
1 : LCD ON
LCD circuit divider division ratio selection bits
b6b5
0 0 : Clock input
0 1 : 2 division of clock input
1 0 : 4 division of clock input
1 1 : 8 division of clock input
LCDCK count source selection bit
0 : f(XCIN)/32
1 :
φSOURCE/8192
LCD mode register 2
(LM2 : address 001416)
b7
b0
Voltage multiplier circuit control bit
0 : Voltage multiplier circuit disabled
(Input ports P70/INT01, P71/INT11)
1 : Voltage multiplier circuit enabled (C1, C2 pins)
VL3 connection bit
0 : Connect LCD internal VL3 to VCC
1 : Connect LCD internal VL3 to VL3 pin
Not used (returns “0” when read)
Segment output disable register 0
(SEG0 : address 0FF416)
b7
b0
Segment output disable bit 0
0 : Segment output SEG8
1 : Output port P00
Segment output disable bit 1
0 : Segment output SEG9
1 : Output port P01
Segment output disable bit 2
0 : Segment output SEG10
1 : Output port P02
Segment output disable bit 3
0 : Segment output SEG11
1 : Output port P03
Segment output disable bit 4
0 : Segment output SEG12
1 : Output port P04
Segment output disable bit 5
0 : Segment output SEG13
1 : Output port P05
Segment output disable bit 6
0 : Segment output SEG14
1 : Output port P06
Segment output disable bit 7
0 : Segment output SEG15
1 : Output port P07
Segment output disable register 1
(SEG1 : address 0FF516)
b7
b0
Segment output disable bit 8
0 : Segment output SEG0
1 : Output port P20
Segment output disable bit 9
0 : Segment output SEG1
1 : Output port P21
Segment output disable bit 10
0 : Segment output SEG2
1 : Output port P22
Segment output disable bit 11
0 : Segment output SEG3
1 : Output port P23
Segment output disable bit 12
0 : Segment output SEG4
1 : Output port P24
Segment output disable bit 13
0 : Segment output SEG5
1 : Output port P25
Segment output disable bit 14
0 : Segment output SEG6
1 : Output port P26
Segment output disable bit 15
0 : Segment output SEG7
1 : Output port P27
Notes 1: When “1” is selected as duty ratio by the duty ratio selection bits,
set “1” to the bias control bit.
2: LCDCK is a clock for the LCD timing controller.
φSOURCE indicates the followings:
XIN input in the frequency/2, 4, or 8 mode
On-chip oscillator divided by 4 in the on-chip oscillator mode
Sub-clock in the low-speed mode
3: Only pins set to output ports by the direction register can be controlled
to switch to output ports or segment outputs by the segment output
disable register.
4: When disabling the voltage multiplier circuit, the C1 and C2 pins
function as input ports P70/INT01, P71/INT11.
Segment output disable register 2
(SEG2 : address 0FF616)
b7
b0
Segment output disable bit 16
0 : Segment output SEG16-SEG19
1 : Output port P10-P13
Segment output disable bit 17
0 : Segment output SEG20-SEG23
1 : Output port P14-P17
Segment output disable bit 18
0 : Segment output SEG24-SEG27
1 : Output port P30-P33
Segment output disable bit 19
0 : Segment output SEG28-SEG31
1 : Output port P34-P37
Not used (do not write “1”)
(1)
(2)
(4)
(3)
相关PDF资料
PDF描述
MC68B05P2L 8-BIT, MROM, 2 MHz, MICROCONTROLLER, CDIP28
MC908QB4MDT 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
MC908QY2AVDWE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
MK2745-20SLF 108 MHz, VIDEO CLOCK GENERATOR, PDSO16
MK2742-04SLFTR 81 MHz, VIDEO CLOCK GENERATOR, PDSO16
相关代理商/技术参数
参数描述
M38D59GFFP#U0 功能描述:IC 740/38D5 MCU QZ-ROM 80QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR)
M38D59GFHP#U0 功能描述:IC 740/38D5 MCU QZ-ROM 80LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR)
M38D59T-RLFS 功能描述:BOARD EMULATOR FOR 38D5 GROUP RoHS:否 类别:编程器，开发系统 >> 内电路编程器、仿真器以及调试器 系列:- 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:*
M38DC-15 制造商:M/A-COM Technology Solutions 功能描述:MIXER(SPEC UX1015) - Bulk
M38K00F1-16FP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*