参数资料
型号: MT46V32M8FG-6TIT:G
元件分类: DRAM
英文描述: 32M X 8 DDR DRAM, 0.7 ns, PBGA60
封装: (8 X 14) MM, PLASTIC, FBGA-60
文件页数: 41/93页
文件大小: 3632K
PDF: 09005aef80768abb/Source: 09005aef82a95a3a
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. O, Core DDR: Rev. B 1/09 EN
44
2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
Notes:
1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Table 33 on page 47) and
after tXSNR has been met (if the previous state was self refresh).
2. This table is bank-specific, except where noted (that is, the current state is for a specific
bank and the commands shown are those allowed to be issued to that bank when in that
state). Exceptions are covered in the notes below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row active: A row in the bank has been activated, and tRCD has been met. No data
bursts/accesses and no register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
4. The following states must not be interrupted by a command issued to the same bank. COM-
MAND INHIBIT or NOP commands, or allowable commands to the other bank should be
issued on any clock edge occurring during these states. Allowable commands to the other
bank are determined by its current state and Table 30 and according to Table 31 on
Precharging: Starts with registration of a PRECHARGE command and ends when tRP is
met. Once tRP is met, the bank will be in the idle state.
Row activating: Starts with registration of an ACTIVE command and ends when tRCD is
met. Once tRCD is met, the bank will be in the “row active” state.
Read with auto precharge enabled: Starts with registration of a READ command with
auto precharge enabled and ends when tRP has been met. Once tRP is met, the bank
will be in the idle state.
Write with auto precharge enabled: Starts with registration of a WRITE command with
auto precharge enabled and ends when tRP has been met. Once tRP is met, the bank
will be in the idle state.
5. The following states must not be interrupted by any executable command; COMMAND
INHIBIT or NOP commands must be applied on each positive clock edge during these states.
Table 30:
Truth Table 3 – Current State Bank n – Command to Bank n
Notes: 1–6 apply to the entire table; Notes appear below
Current State
CS#
RAS#
CAS#
WE#
Command/Action
Notes
Any
H
XXX
DESELECT (NOP/continue previous operation)
L
HHH
NO OPERATION (NOP/continue previous operation)
Idle
LL
H
ACTIVE (select and activate row)
LL
L
H
AUTO REFRESH
LL
LOAD MODE REGISTER
Row active
LHL
H
READ (select column and start READ burst)
LHL
L
WRITE (select column and start WRITE burst)
LL
H
L
PRECHARGE (deactivate row in bank or banks)
Read
(auto precharge
disabled)
LHL
H
READ (select column and start new READ burst)
LHL
L
WRITE (select column and start WRITE burst)
LL
H
L
PRECHARGE (truncate READ burst, start PRECHARGE)
LH
HL
BURST TERMINATE
Write
(auto precharge
disabled)
LHL
H
READ (select column and start READ burst)
LHL
L
WRITE (select column and start new WRITE burst)
LL
H
L
PRECHARGE (truncate WRITE burst, start
PRECHARGE)
相关PDF资料
PDF描述
MT46V32M8BG-6AT:G 32M X 8 DDR DRAM, 0.7 ns, PBGA60
M29F800FB55N3E2 512K X 16 FLASH 5V PROM, 55 ns, PDSO48
MC12L1NZGF ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.25A, 28VDC, PANEL MOUNT-THREADED
MD00S1NCQF ROTARY SWITCH-6POSITIONS, DP6T, LATCHED, 0.25A, 28VDC, THROUGH HOLE-STRAIGHT
MD06L1NZGD ROTARY SWITCH-6POSITIONS, DP6T, LATCHED, 0.25A, 28VDC, PANEL MOUNT-THREADED
相关代理商/技术参数
参数描述