- 您现在的位置：买卖IC网 > PDF目录268181 > NAND01GW3B2AN6F (NUMONYX) 128M X 8 FLASH 3V PROM, 25000 ns, PDSO48 PDF资料下载
参数资料
| 型号： | NAND01GW3B2AN6F |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | 128M X 8 FLASH 3V PROM, 25000 ns, PDSO48 |
| 封装： | 12 X 20 MM, LEAD FREE, PLASTIC, TSOP-48 |
| 文件页数： | 10/64页 |
| 文件大小： | 632K |
| 代理商： | NAND01GW3B2AN6F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
Signal descriptions
NAND01G-B, NAND02G-B
18/64
3.7
Power-Up Read Enable, Lock/Unlock Enable (PRL)
The Power-Up Read Enable, Lock/Unlock Enable input, PRL, is used to enable and disable
the lock mechanism. When PRL is High, VIH, the device is in Block Lock mode.
If the Power-Up Read Enable, Lock/Unlock Enable input is not required, the PRL pin should
be left unconnected (Not Connected) or connected to VSS.
3.8
Write Enable (W)
The Write Enable input, W, controls writing to the Command Interface, Input Address and
Data latches. Both addresses and data are latched on the rising edge of Write Enable.
During power-up and power-down a recovery time of 10s (min) is required before the
Command Interface is ready to accept a command. It is recommended to keep Write Enable
high during the recovery time.
3.9
Write Protect (WP)
The Write Protect pin is an input that gives a hardware protection against unwanted program
or erase operations. When Write Protect is Low, VIL, the device does not accept any
program or erase operations.
It is recommended to keep the Write Protect pin Low, VIL, during power-up and power-down.
3.10
Ready/Busy (RB)
The Ready/Busy output, RB, is an open-drain output that can be used to identify if the P/E/R
Controller is currently active. When Ready/Busy is Low, VOL, a read, program or erase
operation is in progress. When the operation completes Ready/Busy goes High, VOH.
The use of an open-drain output allows the Ready/Busy pins from several memories to be
connected to a single pull-up resistor. A Low will then indicate that one, or more, of the
memories is busy.
Refer to the Section 11.1: Ready/Busy Signal electrical characteristics for details on how to
calculate the value of the pull-up resistor.
3.11
VDD Supply Voltage
VDD provides the power supply to the internal core of the memory device. It is the main
power supply for all operations (read, program and erase).
An internal voltage detector disables all functions whenever VDD is below VLKO (see
program/erase during power-transitions.
Each device in a system should have VDD decoupled with a 0.1F capacitor. The PCB track
widths should be sufficient to carry the required program and erase currents.
相关PDF资料 |
PDF描述 |
|---|---|
| NAND08GW3B2CZC1 | 1G X 8 FLASH 3V PROM, 35 ns, PBGA63 |
| NAND01GR3B3CZA1 | 128M X 8 FLASH 1.8V PROM, 35 ns, PBGA63 |
| NAND02GR4B2BZB1 | 128M X 16 FLASH 1.8V PROM, 35 ns, PBGA63 |
| NCH030A3-FREQ-OUT27 | CRYSTAL OSCILLATOR, CLOCK, 1 MHz - 4 MHz, HCMOS OUTPUT |
| NTHA3JAA3-FREQ-OUT27 | CRYSTAL OSCILLATOR, CLOCK, 1 MHz - 4 MHz, HCMOS OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NAND01GW3B2AN6T | 功能描述:闪存 NAND & S.MEDIA FLASH RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND01GW3B2AZA1 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GW3B2AZA6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GW3B2AZA6E | 功能描述:闪存 NAND MEDIA FLASH RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND01GW3B2AZA6F | 制造商:Micron Technology Inc 功能描述:FLASH PARALLEL 3.3V 1GBIT 128MX8 25US 63VFBGA - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。